Bargain Bin

Lock Nuts 6-32 (bag of 100pc)

The HobbyKing helicopter pitch gauge is made from ultra-rigid fiberglass board and features dual ball bearings to ensure accurate measurements every time. This pitch gauge is supplied in kit form to keep production costs down which means we can pass the savings on to you!

Specs:
Measurement: +/- 20 Deg
Size: 145mm x 105mm
Max Blade Width: 80mm

Note: An assembly guide can be found in the FILES tab below.

Use this adapter to convert an XT-60 Charge lead for charging JST equiped batteries. 

Super Kinetic - Replacement Motor Mount

Super Kinetic - Replacement Canopy

HobbyKing® Bix3 Trainer 1550mm - Replacement Tail Wheel

HobbyKing® Bix3 Trainer 1550mm - Replacement Control Rod Set

Diff. Case - BSR 1/8 Rally

Hobbyking™ Hardened Steel Pinion gears are the last pinion gears you will ever need to purchase. The Pinion gears are machined from a special steel alloy and are hardened for ultimate strength and durability. During the manufacturing process, extremely tight tolerances are maintained so the pitch of the gear is precise. This means Hobbyking™ Pinion gears run very quietly and efficiently.

As Brass or Aluminum gears wear, the interface between the pinion and spur gears degrade. The hardened Pinions are so tough that you can eliminate the need for spare gears in your toolbox. The Pinion gears are also strong enough to survive any insane power system that you choose to fit in your 3D helicopter.

Specs:
Pitch: 0.7M
Tooth Count: 12T
Fits Shaft Size: 6mm
Weight: 2.65g

Durafly™ EFX Racer - Replacement Battery Hatch (Red)

This set consists of the lower front fuselage skid plate and the wing center section/belly skid plate for the Durafly EFX Racer series of airplanes.

Basher RZ-4 1/10 Rally Racer - Composite Rear Upright (2pcs)

Doll Stand - Basher PBull 1/18 4WD Desert Buggy

Clear Body - Basher PBull 1/18 4WD Desert Buggy

TrackStar Shock End Caps 12mm (4)

Compatible with the following Shock Absorbers
S12400, S160023, S160026, S160085, S160100

TrackStar Big Bore Suspension Spring Retainer 13mm (4) S124103

Compatible with the following Shock Absorbers
S124300, S160323, S160326

TrackStar Shock Bottom Cap Set with O-Ring S120052

Compatible with the following Shock Absorbers
S12400, S160023, S160026, S160085, S160100, S124300, S160323, S160326

TrackStar Suspension Spring (x4)

Specs:
Wire Thickness: 1.1mm
Internal Diameter: 14mm
Length: 55mm
Spring Rate:  1.2Kg
Color: Gold

Compatible with the following Shock Absorbers
S160023, S160026, S160323, S160326

TrackStar Suspension Spring (x4)

Specs:
Wire Thickness: 1.1mm
Internal Diameter: 14mm
Length: 65mm
Spring Rate:  1.8Kg
Color: Silver

Compatible with the following Shock Absorbers
S160085, S160100

TrackStar Suspension Spring (x4)

Specs:
Wire Thickness: 1.1mm
Internal Diameter: 14mm
Length:65mm
Spring Rate:  1.2Kg
Color: Blue

Compatible with the following Shock Absorbers
S160085, S160100

Aluminum Rear Lower Suspension Arm (2Pcs/Bag) - A2003T, A2027, A2029, A2035 and A3007

6 LED Strip RED

Specifications:
Weight: 10g
Lead Length: 81cm
Plug: JR

Getting wheel pants mounted to your undercart and getting them to stay there has been a problem for many years, not anymore, with the Sullivan adjustable brackets this job has now been made very much easier. The brackets are very strong, they are made of high strength heat treated steel, they can also be adjusted for "give" so that you do not damage the wheel pants on a heavy landing. These mounts will fit 3/16" (4.8mm) axles and music wire and the wheel pants can be either glued or bolted to the brackets.

Please note:  2 brackets are supplied but this is only enough for 1 wheel pant, you will require 2 packs for a standard 2 wheel undercart.

This is a great tool for measuring the main blade pitch on your flybarless or flybar helicopter head. It is designed to hold your smartphone while using a leveling application to measure your heli blade's degrees of pitch. There are many free applications available for download on your smartphone that will work for this purpose. Just be sure to download one that displays the measurement in degrees.

This handy tool is constructed from lightweight yet rigid glass fiber. It features spring loaded foam padded mount posts which will accommodate holding of just about any smartphone. This tool is especially helpful when measuring blade pitch on your flybarless helicopter head since there is no flybar to use for reference with a traditional style pitch gauge.

Note: All necessary hardware is included. Just add your own smartphone after downloading one of the many free IOS/Android leveling applications.

Specs:
Maximum height of adjustable mount posts: 95mm
Maximum width of main blade: 75mm

When it comes to hardware, quality does matter! These titanium machine screws not only offer improved strength over steel, they are also much lighter in weight. These are ideal for use in performance models where shaving weight is absolutely critical, or for any project requiring high strength, lightweight hardware.

Spec.:
Size: M2 x 6mm
Weight: 0.07g(Each)

When it comes to hardware, quality does matter! These titanium machine screws not only offer improved strength over steel, they are also much lighter in weight. These are ideal for use in performance models where shaving weight is absolutely critical, or for any project requiring high strength, lightweight hardware.

Spec.:
Size: M2.5 x 4mm
Weight: 0.10g(Each)

When it comes to hardware, quality does matter! These titanium machine screws not only offer improved strength over steel, they are also much lighter in weight. These are ideal for use in performance models where shaving weight is absolutely critical, or for any project requiring high strength, lightweight hardware.

Spec.:
Size: M4 x 8mm
Weight: 0.50g(Each)

When it comes to hardware, quality does matter! These titanium machine screws not only offer improved strength over steel, they are also much lighter in weight. These are ideal for use in performance models where shaving weight is absolutely critical, or for any project requiring high strength, lightweight hardware.

Spec.:
Size: M4 x 12mm
Weight: 0.65g(Each)

When it comes to hardware, quality does matter! These titanium machine screws not only offer improved strength over steel, they are also much lighter in weight. These are ideal for use in performance models where shaving weight is absolutely critical, or for any project requiring high strength, lightweight hardware.

Spec.:
Size: M2.5 x 4mm
Weight: 0.18g(Each)

When it comes to hardware, quality does matter! These titanium machine screws not only offer improved strength over steel, they are also much lighter in weight. These are ideal for use in performance models where shaving weight is absolutely critical, or for any project requiring high strength, lightweight hardware.

Spec.:
Size: M4 x 8mm
Weight: 0.55g(Each)

Ever damaged your model trying to separate difficult plugs? Frustrated by tight connectors? Turnigy to the rescue with their EasyOff Plug Disconnect system. These handy little clip-on adapters slip onto your T-plug connector and permanently stay in place. A special separator tool slips in between these clips, allowing you to effortlessly separate the plugs. It is a great addition for all your batteries or speed controls, but is very useful for tight battery hatch areas on airplanes and gliders.

The EasyOff plug adapters are universal fit between male and female plugs. They clip into place, though we recommend a small drop of CA glue for the ultimate hold. These are design for XT Branded T-plugs with molded grip detail.

This set includes the separator tool. Additional adapter sets for T-plugs are available here

Also available for XT-60

Specs:
Plug Type: T-Plug
Qty: 20
Weight: 0.9g (pair)

Great for protecting battery packs, combining batteries or covering an ESC etc.

Upgrade your Quanum DIY FPV V2 Goggles with this V2 add on kit.  It incorporates many new features that you have all been asking for and will effectively bring your V2 Goggle set up to V2Pro specs at minimal cost. 

A new, clear acrylic three lens set (1X, 1.25X or 1.5X magnification) and lens frame adapter providing a superior improvement in quality over the previous fresnel lens set. 

A battery pouch with velcro flap and buckle has been added and is excellent for mounting your battery on to the goggle's headstrap (behind the user's head) and will take a battery up to 77mm x 35mm x 22mm.

An EVA foam adapter for mounting a smartphone onto your goggles will turn your V2's into a Virtual Reality headset for gaming etc. Recommended for smartphone sizes up to Samsung Galaxy S6. Smartphone ports are accessible on the ends and the V2's neoprene glove front straps will hold it in place.

Extra comfortable sponge rubber strips with double sided tape have been added for extra cushioning when wearing the goggles and are simply cut to size to match the users requirements. 

Features:
• New clear acrylic lens set and frame (1.0X, 1.25X and 1.50X magnification)
• Battery pouch
• Metal “S” loop for top strap adjustment to improve wearer comfort and fitting
• Extra comfortable sponge rubber cushoining strips for facial comfort
• EVA foam adapter for smartphone for mounting
• A set of extension/conversion cables including:
      a) 3.5mm female phone jack to 2.5mm male phone plug adapter
      b) FPV DC jack to 1x5521 DC plug, 2x3315 DC plug (Length = 350mm)
      c) 3.5mm phone female to RCA male cable (Length = 150mm)
      d) XT60 male to FPV DC jack (Length = 210mm)
      e) 3.5mm phone female to RCA female cable (lenght = 150mm)

Note: A set of modification instructions are located in the "Files" tab below showing the alternate mounting method for the goggle monitor allowing for an increase in focal plane length.

Also available for use with this product:

Quanum DIY FPV Goggle V2Pro Upgrade Glove (Urban Digital Cam)

Quanum DIY FPV Goggle V2Pro Upgrade Glove (Black/Red)

Quanum DIY FPV Goggle V2Pro Upgrade Glove (Fluro Pink)