Bargain Bin

The LM35 Linear Temperature Sensor Module can be used to detect ambient air temperature. This sensor offers a functional range between -40 degree Celsius to 150 degree Celsius. Sensitivity is 10mV per degree Celsius. The output voltage is proportional to the temperature. It is commonly used as a temperature measurement sensor. It includes thermocouples, platinum resistance, thermal resistance and temperature semiconductor chips, which are commonly used in high temperature measurement thermocouples. Platinum resistance temperature used in the measurement of 800 degrees Celsius, while the thermal resistance and semiconductor temperature sensor suitable for measuring the temperature of 100-200 degrees or below, in which the application of a simple semiconductor temperature sensor has good linearity and high sensitivity. The LM35 linear temperature sensor and sensor-specific expansion of Arduino board, in combination, can be very easy to achieve.

Specs:
Sensitivity: 10mV per degree
Celcius Functional range: -40 degree Celsius to 150 degree Celsius

*Note: This is not an original Arduino brand product.

Arduino 6-DOF IMU Module Attitude Control 6DOF 3205 345

*Note: This is not an original Arduino brand product.

Arduino 10DOF with ITG-3205, ADXL345, HMC5883L, and BMP085

*Note: This is not an original Arduino brand product.

Keep your Telemetry Radios safe! These cases are made out of slightly translucent ABS plastic, so you still can see TX/RX LEDs. They have a very tight fit and finish and are clearly labeled. These cases will make your setup look like Pro gear, while keeping them safe!

Designed to fit FPV Radio Telemetry Kit - 915Mhz/433MHz(#42846/42847,not included), But fits other brand Telemetry Radios as well.

Includes:
3M Foam Double-tape X1
Ground module Case X1
Air module Case X1

The flight mode switcher has been designed for open source autopilots such as APM, PX4 and Pix etc. It can switch the flight mode accurately and quickly and replaces the troublesome 2 stage and 3 stage switchers.

Users can set the parameters for the flight mode switcher on the unit and choose the most suitable modes for their requirements. The flight mode switcher features a stable performance, is easy to set up and is small and lightweight.

Typical flight modes are as follows:
• STA (Stabilized) Model will automatically level itself
• SIM (Simple) Allows you to control the movement of the model from the pilots point of view regardless of which way the model is facing
• ALT (Altitude Hold) When this mode is selected it will hold this altitude
• LOI (Loiter) Allows model to hover in the same spot on its own without any input from the pilot
• AUT (Auto) The model will follow a pre-programmed course stored in the autopilot
• RTL (Return to land) Once selected the model will return and land at the point of take-off

The flight mode switcher is simple to install on your transmitter but it is not "plug & play", there is a small amount of soldering involved inside the Tx. See under the "Files" tab for installation instructions.

Once installed on your transmitter and set up in "Mission Planner" it is very simple to use, just press the relevant mode button on the switcher and the model will go into that mode. There is an indicator light to show which mode has been selected and is in use.

Features:
• Allows the user to easily set 6 flight modes
• Simple and straightforward to install
• Compact and lightweight
• Status indicator lights

Specs:
Type: Flight Mode Switcher
Working Voltage: 3~5V
Modes: 6 selectable
Operating Temperature: -10°C~+60°C
Dimensions: 59 x 29 x 9.3mm
Weight: 13g

Included:
Flight Mode Switcher
Connection harness

KingKong Multirotor Propeller 6x4 CW/CCW Green (20pcs)

Includes:
10 x 6040 Propellers (CW)
10 x 6040 Propellers (CCW)

KingKong Multirotor Propeller 6x4 CW/CCW Black (20pcs)

Includes:
10 x 6040 Propellers (CW)
10 x 6040 Propellers (CCW)

Circular polarized antenna's aka "clover leaf antennas" are a great way to increase the performance of your FPV system. The circular polarization helps reject “multipath interference”, a problem that plagues standard dipole stock antennas. Proven to increase range and video clarity, circular polarized antennas have become the standard after-market 'essential' upgrade for modern FPV systems. This is a matched 3 leaf Tx to 4 leaf RX set with no cable length for a nice clean, direct install with RP-SMA connectors.

Specs:
Frequency Range: 900MHz
Impedance: 50ohm
VSWR: <1.5
Gain: 5db
Connector: RP-SMA
Cable: RG141
Cable Length: 0m

The flying V is perhaps the best general purpose antenna in the lower frequencies. Suitable for medium range and altitude, this antenna has slightly lower gain verses the coaxial connected Dipole, however has a very uniform radiation pattern. This is perfect for acrobatic and sport flying where antenna polarization (angle) can vary. The 120 deg V gives the best compromise between radiation pattern and gain.

Specs:
Frequency: 1.3GMHz
Connection: RP-SMA
dbi: 1.9

This 2 piece carbon fiber landing gear is lightweight but very stiff and with high torsional strength, the legs are also streamlined to reduce drag. Designed for fuselages with a minimum width of 170mm, however the legs can be spaced apart to fit aircraft with a much wider fuselage. 

Specs:
Fuselage Width: 170mm
Height: 280mm
Wheel Track: 580mm
Weight: 315g

Super tough glass fiber tube, perfect for fixed wing and multi rotor projects. 

Specs:
Outer Diameter: 8mm
Bore Diameter 5mm
Length: 330mm

Aluminum alloy neck strap adjuster suitable for DJI transmitters or similar.

2mm 2 Blade CNC Folding Propeller Adapter CW & CCW (Gold)

Perfect for multi-rotors, pack comes complete with M2.5 mounting screws for the folding propeller blades.

Specs:
Suits Motor Shafts: 2mm
Blade Thickness: 3mm
Blade Mounting: M2.5
Direction: 1 x Clockwise, 1 x Counterclockwise
Material: Aluminum
Color: Gold
Weight: 6g each

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3mm
Prop bolt dia: 2.5mm
Prop hole spacing: 18mm center to center
Dimensions: 25 x 8 x 9mm
Weight: 8g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3mm
Prop bolt dia: 2.5mm
Prop hole spacing: 18mm center to center
Dimensions: 25 x 8 x 9mm
Weight: 8g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 10g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3.17mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3.17mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3.17mm
Prop bolt dia: 2.5mm
Prop hole spacing: 18mm center to center
Dimensions: 25 x 8 x 9mm
Weight: 8g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3.17mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3.17mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 40g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3.17mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3.17mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 40g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3.17mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3.17mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 40g (Pair)

5 x 3 Folding Propeller Blades 1 Set CW and 1 Set CCW (Blue)

Perfect for 250 style multiracers and multicopters, each blade is manufactured from nylon and is fitted with a brass insert for strength through the blade root.

Specs:
Diameter: 5ins
Pitch: 3ins
Root Thickness: 2.4mm
Mounting Hole: 2mm
Rotation: 1 pair clockwise, 1 pair counterclockwise
Color: Blue
Weight: 0.12g each blade

8 x 4.5 Folding Propeller Blades 1 Pair CW and 1 Pair CCW (Blue)

Perfect for medium size multicopters, each blade is manufactured from nylon and is fitted with a brass insert for strength through the blade root.

Specs:
Diameter: 8ins
Pitch: 4.5ins
Root Thickness: 3mm
Mounting Hole: 3mm
Direction: 1 pair clockwise, 1 pair counterclockwise
Color: Blue
Weight: 3g each blade

8 x 4.5 Folding Propeller Blades 1 Pair CW and 1 Pair CCW (Yellow)

Perfect for medium size multicopters, each blade is manufactured from nylon and is fitted with a brass insert for strength through the blade root.

Specs:
Diameter: 8ins
Pitch: 4.5ins
Root Thickness: 3mm
Mounting Hole: 3mm
Direction: 1 pair clockwise, 1 pair counterclockwise
Color: Yellow
Weight: 3g each blade

9 x 4.7 Folding Propeller Blades 1 Pair CW and 1 Pair CCW (Green)

Perfect for medium size multicopters, each blade is manufactured from nylon and is fitted with a brass insert for strength through the blade root.

Specs:
Diameter: 9ins
Pitch: 4.7ins
Root Thickness: 3mm
Mounting Hole: 3mm
Direction: 1 pair clockwise, 1 pair counterclockwise
Color: Green
Weight: 3.4g each blade

Great performance and super value!  and thats exactly what you need for your multirotor, a tough but expendable prop that wont break the bank to replace.

Packaged as a set of 2, with one CW rotation and one CCW rotation you can afford to stock up on these great value props.

Available in 6 colors, they can be mixed and matched to help with multirotor orientation or simply give your model a unique and cool look.  

Specs:
Size:5040 (5x4)
Color: Green
Hub: 5mm
Material: Glass Reinforced Plastic/Nylon

Includes:
1 x CW rotation
1 x CCW rotation

Great performance and super value!  and thats exactly what you need for your multirotor, a tough but expendable prop that wont break the bank to replace.

Packaged as a set of 2, with one CW rotation and one CCW rotation you can afford to stock up on these great value props.

Available in 6 colors, they can be mixed and matched to help with multirotor orientation or simply give your model a unique and cool look.  

Specs:
Size:5040 (5x4)
Color: Orange
Hub: 5mm
Material: Glass Reinforced Plastic/Nylon

Includes:
1 x CW rotation
1 x CCW rotation

Futaba Trainer Cable (Buddy Box Cable) 2.8m

The Turnigy Voltage Protector helps prevent your receiver from dropping below its required operating voltage. This helps to eliminate "brownouts" and prevents your receiver from rebooting. It will also help reduce the load on your ESC's BEC and reduce the likelihood of glitching. Simply plug it into any spare channel on your receiver.

Operating Voltage : 3.2V - 11.1V (1s ~ 3s LiPo)
Capacitor voltage: 16v
Storage Capacity: 3300uf
Weight: 6.1g

Turnigy TY-P1 25Amp Brushless ESC Programming Card

Programming Options:
Brake (OFF/ON).
Cut-off Type (Soft-cut/Cut-off).
Cut-off Voltage (Low / Middle / High ).
Start Mode (Normal / Soft / Very Soft ).
Timing Mode (Low / Middle / High).
Cell (Auto, 2S, 3s, 4S).

Losi Mini Plug Pigtail - Battery (2pcs/bag)

7cm wire with pre-tinned ends.

Our Wire Mesh Guard is an excellent way to protect servo leads or battery wires. The mesh expands to 4x original size and comes in a variety of colors.

Specs:
Diameter: 3mm before expansion
Length: 2m
Color: Neon Yellow

Replacement thumb screw for RJX CAOS 330

Includes
1x thumb screw

Alloy Prop Saver & Adapter w/ Band
Weight: 2.5g

Please select below for your size;
Available: 2.3mm

Walkera Runner 250(R) Racing Quadcopter - Propellers (1CW/1CCW)

Runner 250(R)-Z-01

Screw Countersunk Phillips M2.5x12mm (10pcs/pack)