Bargain Bin

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3.17mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3.17mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 40g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3.17mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3.17mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 40g (Pair)

Futaba Trainer Cable (Buddy Box Cable) 2.8m

The Turnigy Voltage Protector helps prevent your receiver from dropping below its required operating voltage. This helps to eliminate "brownouts" and prevents your receiver from rebooting. It will also help reduce the load on your ESC's BEC and reduce the likelihood of glitching. Simply plug it into any spare channel on your receiver.

Operating Voltage : 3.2V - 11.1V (1s ~ 3s LiPo)
Capacitor voltage: 16v
Storage Capacity: 3300uf
Weight: 6.1g

Turnigy TY-P1 25Amp Brushless ESC Programming Card

Programming Options:
Brake (OFF/ON).
Cut-off Type (Soft-cut/Cut-off).
Cut-off Voltage (Low / Middle / High ).
Start Mode (Normal / Soft / Very Soft ).
Timing Mode (Low / Middle / High).
Cell (Auto, 2S, 3s, 4S).

Losi Mini Plug Pigtail - Battery (2pcs/bag)

7cm wire with pre-tinned ends.

Our Wire Mesh Guard is an excellent way to protect servo leads or battery wires. The mesh expands to 4x original size and comes in a variety of colors.

Specs:
Diameter: 3mm before expansion
Length: 2m
Color: Neon Yellow

Replacement thumb screw for RJX CAOS 330

Includes
1x thumb screw

Alloy Prop Saver & Adapter w/ Band
Weight: 2.5g

Please select below for your size;
Available: 2.3mm

Screw Countersunk Phillips M2.5x12mm (10pcs/pack)

Most standard 7S lithium polymer battery packs feature two balance ports, a 4S and 3S balance lead (total 7S). This makes it difficult to charge with most standard battery chargers that only feature one balance port.

With this super useful adapter you can easily charge your 7S battery with any standard 8~10S capable balance charger that accepts JST-XH balance plugs. This adapter takes the 4S and 3S individual plugs from your pack, and combines them to one single 7S balance plug which is able to connect to most standard 8~10S capable chargers.

Specs:
Input: 1 x 4S and 1 x 3S JST-XH balance plug
Output: 7S JST-XH balance plug
Length: 100mm

Manifold 1set(nickel plating) - A3007

A quick and easy way to eliminate a built in BEC without the need to cut or modify your ESC wires.

Futaba 6pin Trainer Port Plug to JR Male Servo plug (1pcs/bag)

EC2 Male - ESC Connector (5pcs/bag)

EC2 Female & Male (5pcs/bag)

T-Connector Harness for 2 Packs in Parallel (1pc)

Spec:
Weight: 9.0g

JST-XH to JST LED Power Distribution Lead - A neat way to power LED's from 3s Lipoly's using the balance plug.



** WARNING: Check Polarity of your setup before connecting this harness.

60mm Molex 1.25 Servo Extension (5pcs/bag)

Spec.
Weight: 0.6g(Each)

This handy connector set will be appreciated by anyone who is dealing with 'Header Pins' on Multirotor boards or any othe type of PCB.

This set consists of a 1 pin housing and 1 female terminal.

120mm Male to Male Jumper Cable Set (10pc)

Specs: 
Length: 120mm
Pin Spacing: 1mm

Molex 2 Pin Cable Female Connector with 220mm x 26AWG Wire

Specs:
Connector: Molex 2 Pin
Colour: Black, Red
Length: 220mm

Molex 3 Cable Female Connector with 230mm x 26AWG Wire.  

Specs:
Connector:  Female Molex 3 pin
Colour: Black, Yellow, White
Length: 230mm

HXT 4mm to T-Connector Battery Adapter Lead (2pc)

This adapter will convert an HXT 4mm equipped battery to a T-Connector for use with a T-Connector equipped ESC or Charge lead.

Spec:
Weight: 7g (Each)

This adapter will convert a T-Connector equipped battery to an HXT 4mm for use with an HXT 4mm equipped ESC or Charge lead.

Spec:
Weight: 10g(Each)

This adapter will convert an HXT 4mm equipped battery to an XT60 for use with an XT60 equipped ESC or Charge lead.

Spec:
Weight: 10g(Each)

105mm Female Molex 1.25 to Twin Male JST-SH 1.0mm Y Lead

JR Male to 2 x JST(Molex) Female 1.00mm (1pc)

This lead converts 2 x JST(Molex) 1.00mm pitch plugged devices to 1 x JR type male plug.

Specs:
Female Plug: 2 x JST(Molex) 1.00mm pitch
Male Plug: JR type
Length Overall: 123mm
Length Each Tail: 46mm

Micro JST(Molex) 1.0mm Pitch Y Lead (1pc)

Y lead for 2 x micro JST(Molex) plugged servo's or ESC.

Specs:
Male Plug: 2 x JST(Molex) 1.00mm pitch
Female Plug: 1 x JST(Molex) 1.00mm pitch
Length Overall: 105mm
Length Each Tail: 43mm

T-Connector to EC5 Battery Adapter (2pcs/bag)

This adapter will convert a T-Connector equipped battery to a EC5 Plug for use with a EC5 equipped ESC or an EC5 Charge lead.

T-Connector to HXT4mm Battery Adapter (2pcs/bag)

This adapter will convert a T-Connector equipped battery to a HXT4mm for use with a HXT4mm equipped ESC or an HXT4mm Charge lead.

HXT3.5mm to XT60 Battery Adapter (2pcs/bag)

This adapter will convert a HXT3.5mm equipped battery to a XT60 for use with a XT60 equipped ESC or a XT60 Charge lead.

This data cable allows you to connect our 433/915MHz V1.1 Radio Telemetry Kits to your Walkera X800 GPS Quadcopter. The X800 flight controller has a data port which actually functions as a standard APM UART connection. The port is a specialized 4-pin connector which will not fit standard Molex style plugs.

This data cable will allow you to plug directly to the X800 FC data port and to our 433/915MHz V1.1 Radio Telemetry air module, allowing full access to wireless telemetry functionality of the APM based X800 flight controller.

Specs:
Connection: 4-pin Walkera style plug to 6-pin Molex style plug
Length: 180mm

*Note: Please see related items below for the compatible 433/915MHz V1.1 Radio Telemetry Kits.