Durafly Auto-G2 Gyrocopter 821mm - Replacement Battery Hatch

Pioneer 1020mm - Replacement Horizontal Stabilizer

La Belle Dame 1180mm - Propeller Nuts

Dolphin Jet EPO 1010mm - Replacement Vertical & Horizontal Tail

Phantom FPV Flying Wing 1550mm - Replacement Motor Cover

The HobbyKing® ™ Walrus is a very capable, fun model that appeals to both new and experienced pilots alike. Easy to fly and easy to build, the Walrus is great value for money!

Made from tough EPO foam, the Walrus is simple to assemble, the colourful decals are pre-applied, and the brushless outrunner motor, ESC, and all servos are pre-installed, even the folding prop and spinner have been factory fitted! As well as being easy to assemble, the Walrus is very practical and features a stiff, CF-reinforced 2pc Plug-in-wing and a large canopy area that allows you to fit a wide range of lipoly packs. Its somewhat portly proportions also make the Walrus super easy to hand-launch. The great-looking scheme is perfect for orientation, and its appealing size gives the Walrus plenty of presence, as well as the ability to handle a little wind.

Introducing our EPP 3D MX2. Featuring a fantastic design and layout, this all out EPP 3D'er will satisfy the most eager 3D pilots!

Its fuselage is torsionally very stiff yet light with loads of space beneath the long top hatch for your radio and power system. The wing is a one-piece affair featuring EPP construction, a very accurate symmetrical airfoil with 2 additional spars to minimize flex and twist. The control surfaces are something else - the elevator, rudder, and ailerons feature a 3 layer construction (Epp-Depron-EPP) making for stiff surfaces and NO flex at extreme throws! Snap rolls "Snap" and the control response is instantaneous.

The light - yet rigid - airframe adds up to one great flying 3D "foamy". Waterfalls, harriers, flat spins, rolling circles this model has the precision to perform these and any other moves you can think of!

Assembly of the airframe in a quick 10-15 minute process with the help of a little medium CA. The radio and power system layouts are very straightforward, the long top hatch making for easy access.

This is a great model for general park flying and hardcore 3D. You will be hard-pressed to break this model, it will take hard knocks and just keep bouncing back every time!


Features:
• Tough EPP material, light-weight, and crash-resistant
• Stiff EPP/Depron composite control surfaces
• Revolutionary design adds to the structural integrity and the rigidity of the airframe
• Light-weight provides optimal wing loading
• Outstanding aerobatic performance and 3D maneuverability.
• Simple design allows for easy equipment access and installation
• The stand out color scheme great for orientation


Specs:
Wingspan: 955mm
Length: 945mm
Wing Area: 15.2dm2
Weight: 550g (without battery)



Requires:
4 channel radio system
2217 950-1100KV Brushless outrunner 
30Amp ESC 
3S 11.1V 1100-1300MAH Li-Po 
10x4.7/11x4.7 propeller 
4 x 9g servos

Telemicro 520mm - Replacement Spinner

Hobbyking Bixler 2 EPO 1500mm - Replacement Pushrod Set

HobbyKing Bixler 2 EPO 1500mm -  Replacement Flap Hinges (6pcs/bag)

Works for both Bixler 2 and Bix3 models.

Hobbyking Bixler 2 EPO 1500mm - Replacement Aileron Hinges (10pcs/bag)

This little kit takes around 4hrs to build and will satisfy the throttle jocky in all of us!

The flycat comes with 56mm EDF and you will need a 25A ESC & 4800kv inrunner.

This plane is extremely fast, (over 100mph!), however still stable at slow flight.

Spec.
WingSpan: 640mm
Length: 800mm
Weight: 290g
BESC : 25A (not included)
Motor: 4800kv 20-30 size Inrunner (not included)
Lipoly: 1300mAh 11.1v 20C (not included)

Required.
Motor & ESC
3 x 9g Servo
5 or 10min Epoxy (Araldite)
1 x Servo Y lead
1 x Servo Extention lead
12AWG Silicon wire (20cm For motor to ESC)
1300mah 11.1v 20C lipo battery
Your own receiver and transmitter

Our flight report.

Kit fits together well, light sanding of leading and trailing edges required to remove extra foam. We chose to not strengthen the wing with CF tubing, which didnt prove to be an issue, even at full speed high G turns.

We opted to mount the BESC being the battery area, in case the battery needed to be moved forward to adjust CofG, however this wasnt necessary.

EDF was mounted on the stick mount. Stick mount was shortened, with the extra piece used to raise the EDF off the stick to clear the EDF shroud. 2 bolts held the fan unit to the stick, one before and one after the fan blades.

First flight.

We kept CofG 9.5cm from the apex of the wings leading edge. The flycat was hand launched at 3/4 throttle, accelerating quickly. To our surprise, no trimming was required.

The flycat is an extremely fast kit to fly, and required a lot of elevator in turns. We suggest putting the elevator on maximum throws. It needs HUGE amounts of elevator during turns!

Overall an excellent plane which flys smoothly, even on windy days.

We suggest a good lipo pack, as this little hotty will chew through a 1500mAh in only 5 minutes. We used the ZIPPY-R 1800mAh 22C 3S1P pack for around 8 minute flights. As compared to the ZIPPY-Q pack which brought us short at about 7 minutes.

Durafly® ™ Micro Series - Replacement Motor Mount

Super Kinetic - Replacement Motor Mount

Super Kinetic - Replacement Canopy

Super Kinetic - Replacement Control Wire - Steel (With Ball Link)

Super Kinetic - Replacement Decals (2pcs/set)

Durafly™ SkyMule 1500mm - Bottom Servo Hatch

HobbyKing® Bix3 Trainer 1550mm - Replacement Control Rod Set

HobbyKing® Bix3 Trainer 1550mm - Replacement Prop Adapter

HobbyKing™ Wingnetic 805mm - Replacement Fuselage

HobbyKing™ Bix3 Trainer 1550mm - Replacement Wing Bolts

2 Pieces Included

Hobbyking™ Super-G Autogyro - Blade Grip Bolts

Includes 3 pieces

Durafly™ EFX Racer - Replacement Fuselage (Yellow)

Durafly™ EFX Racer - Replacement Battery Hatch (Red)

Durafly™ EFX Racer - Replacement Battery Hatch (Yellow)

Durafly™ EFX Racer - Replacement Horizontal Stabilizer

Durafly™ EFX Racer - Replacement Cowl (Yellow)

Durafly® ™ Tundra - Horizontal Tail / Elevator. This assembly is suitable for the V1, V2, and the Night versions of the Tundra.

Durafly® ™ Tundra - Foam Canopy / Battery Hatch w/Magnet

A replacement tail wheel assembly with wheel that is suitable for the 1300mm Tundra V1, V2, V3, and Night.

A kit of plywood parts for the Durafly Tundra V1, V2, V3, and Night to build a mount/tray for your FPV equipment. The Tundra series is the perfect mount for FPV flying due to its stability and slow flying characteristics.

The Walrus is an extremely stable RC plane for the new flyer to the seasoned pro. Now you can light up the sky and enjoy the fun of night flying. LED super bright lights will light up your nightlife!

If you’re craving speed, the EFXtra is where it’s at, with out of the box performance in excess of 100mph+. Durafly retained the spirit of the EFX Racer and focused on adding extra performance, like the incredible roll and climb rates.

There are plenty of high-performance features and new additions over the EFX Racer. The Durafly EFXtra boasts a new clipped wing (975mm) to give extreme roll rates. An upgraded 3536-1780kv brushless motor (using ultra-high-speed Japanese bearings) with a 60A Aerostar ESC has been added and optimized, for up to 4S performance. Higher speed, higher torque digital 9g servos (metal geared on the ailerons) together with ball link connectors provide true precision control of all surfaces no matter what speed you are traveling. We’ve even included FPV mount in the box for the Adeline junkies that love to live life on the edge.