Aircraft

Telemicro 520mm - Replacement Spinner

This little kit takes around 4hrs to build and will satisfy the throttle jocky in all of us!

The flycat comes with 56mm EDF and you will need a 25A ESC & 4800kv inrunner.

This plane is extremely fast, (over 100mph!), however still stable at slow flight.

Spec.
WingSpan: 640mm
Length: 800mm
Weight: 290g
BESC : 25A (not included)
Motor: 4800kv 20-30 size Inrunner (not included)
Lipoly: 1300mAh 11.1v 20C (not included)

Required.
Motor & ESC
3 x 9g Servo
5 or 10min Epoxy (Araldite)
1 x Servo Y lead
1 x Servo Extention lead
12AWG Silicon wire (20cm For motor to ESC)
1300mah 11.1v 20C lipo battery
Your own receiver and transmitter

Our flight report.

Kit fits together well, light sanding of leading and trailing edges required to remove extra foam. We chose to not strengthen the wing with CF tubing, which didnt prove to be an issue, even at full speed high G turns.

We opted to mount the BESC being the battery area, in case the battery needed to be moved forward to adjust CofG, however this wasnt necessary.

EDF was mounted on the stick mount. Stick mount was shortened, with the extra piece used to raise the EDF off the stick to clear the EDF shroud. 2 bolts held the fan unit to the stick, one before and one after the fan blades.

First flight.

We kept CofG 9.5cm from the apex of the wings leading edge. The flycat was hand launched at 3/4 throttle, accelerating quickly. To our surprise, no trimming was required.

The flycat is an extremely fast kit to fly, and required a lot of elevator in turns. We suggest putting the elevator on maximum throws. It needs HUGE amounts of elevator during turns!

Overall an excellent plane which flys smoothly, even on windy days.

We suggest a good lipo pack, as this little hotty will chew through a 1500mAh in only 5 minutes. We used the ZIPPY-R 1800mAh 22C 3S1P pack for around 8 minute flights. As compared to the ZIPPY-Q pack which brought us short at about 7 minutes.

Durafly® ™ Micro Series - Replacement Motor Mount

Are you ready to be the Red Baron of your local park?  Well with the fantastic Von Stik you can be a flying ace in minutes.   

A great slow stick design, the Von Stik has been made to be a super light, fly anywhere model, with a powerful geared motor running off  a 1S 3.7V 400mAh lipoly battery.  

Supplied with its own 2.4Ghz radio for interference free flying, easy to assemble and finished in a striking Red Baron finish, with the Von Stik you will be making diving attacks and strafing runs in no time at all.

It's easy to fly with its basic rudder and elevator control system and is very forgiving for the novice pilot.  In fact, the Von Stik makes for a perfect first model for any young person or even for the experienced pilot who is looking for a totally fun-fly aircraft that can be thrown up in a local park without any fuss.

Features:
• 2.4Gh radio system
• Light weight
• Easy to assemble
• Rudder/Elevator model
• Perfect for beginners 
• Beautiful bold "Red Baron" finish

Specs:
Wingspan: 52cm
Length: 38cm
RC System: 2.4Ghz
Propeller: 6050 (slowfly)
Weight: 75g
Battery Required: 1S 3.7V 350-400mAh Lipoly
Control Distance: 150m 
Mode: 2

This H-King version of this very impressive F-16 Fighting Falcon is manufactured in EPO foam and is beautifully finished in an authentic USAF color scheme with the decals pre-applied at the factory. The H-King F-16 has outstanding flight characteristics in its own right, it flies like it is on rails, but the pre-installed ORX 6-axis gyro takes this to another level. Pilots of all levels of experience will benefit from using the intermediate gyro setting, this really does improve stability and smoothes out the flight, especially in windy conditions. For beginners and low hours pilots, the flight stabilization system makes it even easier to fly. It utilizes a 32bit MCU for ultra-fast control response and has 3 settings, gyro off, gyro on, and training mode. In the training mode, the gyro gives full stability and also limits the amount of roll and pitch that can be used. In gyro-on mode, this gives slightly less aided stability and does not limit the roll or pitch that can be used, perfect for smooth, jet-style aerobatics. In gyro off mode, it is exactly that, no gyro at all.

This beautiful model of a North American T-28 Trojan USAF Military Trainer with brushed 1020 motor, and 3D/6G gyro stabilization system not only looks great, but it flies great as well. The built-in switchable 6-axis gyro flight stabilization system makes it perfect for both beginners and experts alike. It is tough too, it's constructed from durable, crash-resistant EPP foam which is light, extremely strong, and ready to take all the knocks and bangs associated with learning to fly.

This beautiful model of a Grumman F8F Rare Bear Reno Racer with brushed 1020 motor, and 3D/6G gyro stabilization system not only looks great, but it flies great as well. The built-in switchable 6-axis gyro flight stabilization system makes it perfect for both beginners and experts alike. It is tough too, it's constructed from durable, crash-resistant EPP foam which is light, extremely strong, and ready to take all the knocks and bangs associated with learning to fly.

Do you feel the need for speed? Then this great-looking, extremely fast Rare Bear Reno Racer from Durafly is for you. It is supplied as a Plug-N-Fly model with minimal parts count, so assembly is quick and simple. There is no gluing required, just one screw holds the tail components in place, and 1 screw for the wing. Battery and radio access is via the large magnetically held canopy hatch, so radio installation and battery changes are very easy and straightforward.

The 550mm XK A300 Beechcraft D17S is manufactured to very high standards in tough EPP foam. It is supplied ready to fly (RTF) complete with a Mode 1-2 switchable 2.4GHz 4 channel RC system, a switchable 6-axis gyro, a powerful, efficient brushless motor with ESC, 2 servos, on-board LED lights, 7.4V 600mAh battery, and a USB charging cable. Assembly is very easy and straightforward, all the necessary parts and tools are supplied to get your Staggerwing ready to fly in less than an hour, you just need to supply 6 x "AA" batteries for the transmitter.

The Dancing Wings Hobby Savage Bobber is a small, lightweight foam model that is quick and simple to build. The full-size Savage Bobber was devised by the Zlin Aviation Company. The Bobber as in the motorcycle world means that it is a stripped-down, customized version of an original. The Savage Bobber is a stripped-down, customized version of its older brother the Savage Classic. It is lighter, more maneuverable, and has a slightly narrower fuselage, and the absence of covering to the rear of the fuselage greatly improves the crosswind handling.

The model is reasonably straightforward to assemble, it is manufactured in pre-painted high-quality EPP foam sheet for the majority of the construction, tough plastic for the open framework rear fuselage, and lightweight balsa for the internal structure. Carbon strips are also included to reinforce and improve the stiffness of the structure. It builds up quickly into a good-looking, fun-to-fly lightweight (only 98g) sports plane that is perfect for indoor or park flying. This ARF kit is supplied with a powerful 1108-4000KV brushless motor, 5A brushless ESC, 5" propeller, and 4 x 2g servos.

The ZOHD Dart 250G is the small brother to the popular Dart XL, it is the world's first high-end sub 250g FPV flying wing. With increasing regulations affecting our hobby, it offers an FPV experience without as much hassle as the bigger, heavier models. You will still need to check your country's regulations, some do require you to register a model airplane with a camera on it even when below 250g. The little Dart 250G offers incredible lifting power despite its size, excellent handling, and portability, which makes it the ideal choice for FPV flying in a small package. Features include an optimized airfoil, dedicated equipment bay for flight controller and GPS, nose camera bay, super durable Teflon-covered underbelly, protected leading edge to the wing, and so much more.

Do you feel the need for speed? Then this great-looking, extremely fast Rare Bear Reno Racer from Durafly is for you. It is supplied as a Plug-N-Fly model with minimal parts count, so assembly is quick and simple. There is no gluing required, just one screw holds the tail components in place, and 1 screw for the wing. Battery and radio access is via the large magnetically held canopy hatch, so radio installation and battery changes are very easy and straightforward.

The ZOHD Dart 250G is the small brother to the popular Dart XL, it is the world's first high-end sub 250g FPV flying wing. With increasing regulations affecting our hobby, it offers an FPV experience without as much hassle as the bigger, heavier models. You will still need to check your country's regulations, some do require you to register a model airplane with a camera on it even when below 250g. The little Dart 250G offers incredible lifting power despite its size, excellent handling, and portability, which makes it the ideal choice for FPV flying in a small package. Features include an optimized airfoil, dedicated equipment bay for flight controller and GPS, nose camera bay, super durable Teflon-covered underbelly, protected leading edge to the wing, and so much more.

This H-King version of this very impressive F-18 Super Hornet is manufactured in EPO foam and is beautifully finished in an authentic USAF color scheme with the decals pre-applied at the factory. The H-King F-18 has outstanding flight characteristics in its own right, it flies like it is on rails, but the pre-installed ORX 6-axis gyro takes this to another level. Pilots of all levels of experience will benefit from using the intermediate gyro setting, this really does improve stability and smoothes out the flight, especially in windy conditions. For beginners and low hours pilots, the flight stabilization system makes it even easier to fly. It utilizes a 32bit MCU for ultra-fast control response and has 3 settings, gyro off, gyro on, and training mode. In the training mode, the gyro gives full stability and also limits the amount of roll and pitch that can be used. In gyro-on mode, this gives slightly less aided stability and does not limit the roll or pitch that can be used, perfect for smooth, jet-style aerobatics. In gyro off mode, it is exactly that, no gyro at all.

The 550mm XK A300 Beechcraft D17S is manufactured to very high standards in tough EPP foam. It is supplied ready to fly (RTF) complete with a Mode 1-2 switchable 2.4GHz 4 channel RC system, a switchable 6-axis gyro, a powerful, efficient brushless motor with ESC, 2 servos, on-board LED lights, 7.4V 600mAh battery, and a USB charging cable. Assembly is very easy and straightforward, all the necessary parts and tools are supplied to get your Staggerwing ready to fly in less than an hour, you just need to supply 6 x "AA" batteries for the transmitter.