Aircraft

Phantom FPV Flying Wing 1550mm - Replacement Vertical Stabilizer (1pair)

Phantom FPV Flying Wing 1550mm - Replacement Main Wing (1pair)

*Note* For V2 version only. V2 has removeable wing panels.

This is a great “bread board” pin ready accelerometer for your Arduino or other microcontroller projects

Features:
• BMA180 three-axis ultra-high performance digital accelerometer, which provides a 14-bit digital output via a 4-wire SPI or 2-wire I 2 C interface
• Full scale measurement range can be set to ± 1g balance, 1.5G, 2G, 3G, 4G, 8G or 16G
• programmable wake-up
• Low-g and high-g detection
• Tap detection
• Slope detection
• Self-test capability
• The sensor also has two operating modes: low noise, low power consumption in a tiny 3x3mm 12-pin LGA package BMA180
• The sensor can be between 1.62 to 3.6V VDD and 1.2 to 3.6V VDDIO supply will typically only consume 650uA standard mode.

Specs:
Size: 21 x 10 x 2.6mm
Voltage: 1.2-3.6v
Output: SPI or I2C

*Note: This is not an original Arduino brand product.

Superheterodyne 3310 Wireless receiver module +315RF Wireless transmitter module 

Arduino 6-DOF IMU Module Attitude Control 6DOF 3205 345

*Note: This is not an original Arduino brand product.

USBasp AVR Programming Device for ATMEL Processors

Includes:
1 x USBasp Device
1 x Cable

Suits the HobbyKing Quadcopter Control Board.

Keep your Telemetry Radios safe! These cases are made out of slightly translucent ABS plastic, so you still can see TX/RX LEDs. They have a very tight fit and finish and are clearly labeled. These cases will make your setup look like Pro gear, while keeping them safe!

Designed to fit FPV Radio Telemetry Kit - 915Mhz/433MHz(#42846/42847,not included), But fits other brand Telemetry Radios as well.

Includes:
3M Foam Double-tape X1
Ground module Case X1
Air module Case X1

The flight mode switcher has been designed for open source autopilots such as APM, PX4 and Pix etc. It can switch the flight mode accurately and quickly and replaces the troublesome 2 stage and 3 stage switchers.

Users can set the parameters for the flight mode switcher on the unit and choose the most suitable modes for their requirements. The flight mode switcher features a stable performance, is easy to set up and is small and lightweight.

Typical flight modes are as follows:
• STA (Stabilized) Model will automatically level itself
• SIM (Simple) Allows you to control the movement of the model from the pilots point of view regardless of which way the model is facing
• ALT (Altitude Hold) When this mode is selected it will hold this altitude
• LOI (Loiter) Allows model to hover in the same spot on its own without any input from the pilot
• AUT (Auto) The model will follow a pre-programmed course stored in the autopilot
• RTL (Return to land) Once selected the model will return and land at the point of take-off

The flight mode switcher is simple to install on your transmitter but it is not "plug & play", there is a small amount of soldering involved inside the Tx. See under the "Files" tab for installation instructions.

Once installed on your transmitter and set up in "Mission Planner" it is very simple to use, just press the relevant mode button on the switcher and the model will go into that mode. There is an indicator light to show which mode has been selected and is in use.

Features:
• Allows the user to easily set 6 flight modes
• Simple and straightforward to install
• Compact and lightweight
• Status indicator lights

Specs:
Type: Flight Mode Switcher
Working Voltage: 3~5V
Modes: 6 selectable
Operating Temperature: -10°C~+60°C
Dimensions: 59 x 29 x 9.3mm
Weight: 13g

Included:
Flight Mode Switcher
Connection harness

The X-CAM A10-3H Gimbal it at the top of the list when it comes to gimbals, the A10 has True continuous rotation 3-Axis ability with A/V Video link transfer. Full control over Roll, Tilt, Yaw, Mode and Zero home. And charging with A/V out transfer for the GoPro hero camera.

There are a lot of 3 Axis gimbals on the market, but only a few that use a slipper for true 360Deg continues rotation and also transfers the A/V output from the GoPro to the top controller for VTX use. The A/V line also powers/charges the GoPro. Another key feature on the X-CAM is its ability to go to zero or home using referencing sensors, this is great for when transitioning from a yaw control to a forward flight mode the gimbal will auto go to the front position.

The A10 uses an advanced method of vibration control and mounting and is a full CNC aluminum frame design with integrated motors for a light 280g weight.

If you’re serious about some aerial Photography with a GoPro this is the gimbal for you

Features:
• Continuous 360deg rotation
• A/V transfer cable with power
• 5 chs of adjustment over Sbus
• Sbus and PPM support
• Home sensors
• GUI and Upgrade ability
• Wide input voltage range
• Aluminum construction

Specs:
Weight:  280g ( without GOPRO )
Stabilization frequency:  5200Hz
Input voltage:  7.4v ~ 16.8v ( 2S ~ 4S Lipo )
Tilt travel:  +-90 degree; Roll travel:  +-45 degree
YAW travel:  360 degrees unlimited rotation

These custom made aluminum extrusions are perfect for you Multi-Rotor DIY projects, no more borrowing moms shower curtain rods...they have internal riffling (ribbing) added to remain ultra-light but have increased strength and anti-vibration characteristics as well as anodized for various color options for orientation and Bling.

Specs:
Diameter:12.8 x 12.8mm (.5inch)
Length: 600mm
Color: Black
weight: 55g

These custom made aluminum extrusions are perfect for you Multi-Rotor DIY projects, no more borrowing moms shower curtain rods...they have internal riffling (ribbing) added to remain ultra-light but have increased strength and anti-vibration characteristics as well as anodized for various color options for orientation and Bling.

Specs:
Diameter:15 x 15mm
Length: 600mm
Color: Black
weight:63g

2mm 2 Blade CNC Folding Propeller Adapter CW & CCW (Gold)

Perfect for multi-rotors, pack comes complete with M2.5 mounting screws for the folding propeller blades.

Specs:
Suits Motor Shafts: 2mm
Blade Thickness: 3mm
Blade Mounting: M2.5
Direction: 1 x Clockwise, 1 x Counterclockwise
Material: Aluminum
Color: Gold
Weight: 6g each

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3mm
Prop bolt dia: 2.5mm
Prop hole spacing: 18mm center to center
Dimensions: 25 x 8 x 9mm
Weight: 8g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3mm
Prop bolt dia: 2.5mm
Prop hole spacing: 18mm center to center
Dimensions: 25 x 8 x 9mm
Weight: 8g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 10g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 10g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3.17mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3.17mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3.17mm
Prop bolt dia: 2.5mm
Prop hole spacing: 18mm center to center
Dimensions: 25 x 8 x 9mm
Weight: 8g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3.17mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3.17mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 40g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3.17mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3.17mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 40g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3.17mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3.17mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 40g (Pair)

Ever wanted to know how fast your motor is spinning?
Wished you could better select the right propeller for your motor?
Now you can more accurately tune and performance test your engine, motor, edf or heli with the Turnigy tachometer.

Measures 2 to 9 propellers.
Super easy to use.
0-99999rpm range

Features:
Ultra sharp backlit LCD
220mah Lion battery included
Auto shut-off when idle. (no more flat batteries)
Weighs only 39g.

TZ-V2 .90 Size Nitro 3D Helicopter Replacement Carbon Main Frames.

RJX X-TRON 500 6 x 12 x 4mm Bearing # X500-8003 (2pcs)

Replacement thumb screw for RJX CAOS 330

Includes
1x thumb screw

Propeller adapter for BE1806 motor 2 x CW

LDPOWER MT2206-1900KV Brushless Multicopter Motor (CW)

Innovators in multicopter technology, LDPOWER, have released their long awaited series of premium multicopter motors. These have been stringently tested to ensure outstanding performance, reliability and durability.

These motors are easy to install, very efficient and have no noise. They come in both CW and CCW formats.

LDPOWER motors are premium quality and will definitely answer the need of serious builders and flyers of quads/multis everywhere.

Specs:
KV(RPM/V): 1900KV
LiPoly cells: 7.4V-11.1V (2S-3S)
Max Power: 323.8W
Max Amps: 25.7A
Dimensions(Dia.xL): 29.5 x 27.7mm
Motor Shaft: 3mm
Prop shaft: 5mm
Weight: 34.7g
Bolt hole spacing: 19mm-M3*2  16mm-M3*2
Connectors: 2mm bullet

Volts  Prop   Throttle  Amps  Watts     RPM     Thrust (g)
7.4    6030   30%     1.8      13.32      8792      85
7.4    6030   50%     2.7      19.98    10341     123
7.4    6030   75%     3.9      28.86    11949     171
7.4    6030   100%    5.3      39.22    13656     228
7.4    6045   30%     2.5      18.5        7107     115.5
7.4    6045   50%     3.7      27.38     8607      164.5
7.4    6045   75%     6.0      44.4     10216      240
7.4    6045   100%    9.2     68.08    12003      335
11.1   6030   30%     3.1     34.41    12140      180
11.1   6030   50%     4.6     51.06    15621      249
11.1   6030   75%     6.9     76.59    16420      350
11.1   6030   100%    10.3   114.33   18953      480
11.1   6045   30%     3.8      42.18     9592      210
11.1   6045   50%     5.8      64.38   11258      292.5
11.1   6045   75%     10.1    112.11  13817      430.5
11.1   6045   100%    16.2    179.82  16315      594.5

This handy little accessory will allow you to easily split a single receiver channel output into five. A handy accessory for those building multicopters as it gives you an easy way to program the throttle range into your ESC's all together prior to fitting them to your frame. It can also be used as a splitter in LED lighting systems.

Spec:
Lead length: 60mm
Weight: 3g

Mini black T Connector pack (5 Pairs)

Specs:
Base Dimensions: 5mm x 8mm
Contact Dimension: 3mm x 5mm x 1mm
Rating: 10amps continuous

Super flexible 26AWG twisted silicone male to male servo lead. These are specifically made as signal leads for RX to Flight controller connections, the light 26AWG silicone wire is so flexible it transfers virtually no vibration to the Flight controller, well the twist helps reduce inducted noise. If used in conjunction of having only one lead vertical and the other leads turned on their side for signal only, makes for a clean and minimal vibration transfer installation. Or better yet a single CPPM/SBUS single lead. 

Specs:
Length: 130mm(black/red/white)
Connection: Male JR style plug on each end.

Super flexible 26AWG twisted silicone male to male servo lead. These are specifically made as signal leads for RX to Flight controller connections, the light 26AWG silicone wire is so flexible it transfers virtually no vibration to the Flight controller, well the twist helps reduce inducted noise. If used in conjunction of having only one lead vertical and the leads turned on their side for signal only makes for a clean and minimal vibration transfer installation, or better yet a single CPPM/SBUS single lead.

Specs:
Length: 80mm(black/red/white)
Connection: Male JR style plug on each end.

This data cable allows you to connect our 433/915MHz V1.1 Radio Telemetry Kits to your Walkera X800 GPS Quadcopter. The X800 flight controller has a data port which actually functions as a standard APM UART connection. The port is a specialized 4-pin connector which will not fit standard Molex style plugs.

This data cable will allow you to plug directly to the X800 FC data port and to our 433/915MHz V1.1 Radio Telemetry air module, allowing full access to wireless telemetry functionality of the APM based X800 flight controller.

Specs:
Connection: 4-pin Walkera style plug to 6-pin Molex style plug
Length: 180mm

*Note: Please see related items below for the compatible 433/915MHz V1.1 Radio Telemetry Kits.

A JST male plug to 2.54mm pitch male jumper lead for a variety of uses.

This lead is the best solution for batteries that are slightly out of balance; simply plug it into the individual cells on the balance lead, select a 1S charge rate and you can charge them one at a time to ensure they are all at optimum charge. 

Only use this method to restore cells that are slightly out of balance and remember that there could be something wrong with one of the cells so keep a close eye on it while charging.

Overall length: 70mm

The Vortex FPV Racer from ImmersionRC is an incredible piece of kit for the serious competitor, but like all things flying the ocassional mishap is inevitable!

This crash kit is a convenient way to keep a stock of all of those plastic parts most likely to be damaged in a serious "departure from controlled flight"

Included are all parts which mount the motors to the carbon fiber arms, the plastic pivot points, foldable arm clips, and all other plastic parts.

No carbon fiber parts are included (see Crash Kit 2.)

Included:
1 x Front bumper (FR4)
2 x Side plates
8 x Arm clips
4 x Arm pivot tops
4 x Arm pivot bottoms
4 x Landing bumpers
4 x Landing mounts
4 x Motor mounts
8 x Hex bushes
1 x Camera support base
1 x Camera support arm
4 x Damper pins
4x Damper circlip
4x Screw HA2x8
4x Screw HA2x6

This handy little device allows you to program your ZYX Flybarless Controller wirelessly via Bluetooth connectivity with your Android device. Now there is no longer a need to bring your PC to the field for making programming adjustments!

Simply plug this device into the data port of your ZYX unit, install the free ZYX programming app on your Android mobile device and you are all set! It's that easy. You will be able to access all of the same programming options that are available on the PC software directly from your Android device.

This is a must have for any ZYX user with an Android mobile device!

Features:
• Compact size
• Easy to use
• Bluetooth wireless connectivity
• Free Android app available
• Eliminates the need to bring your PC to the field

Specs:
Dimensions: 32x14x5mm
Weight: 3g

*Note: This device currently supports Android 1.6 and above versions of the operating system.

Tarot 450 Pro/Pro V2 DFC Feathering Spindle (TL48016)

The Tarot 450 Pro/Pro V2 DFC feathering spindles are uniquely designed to reduce the probability of the retaining screws coming loose.

Includes:
450 DFC Feathering Spindle x 1 (4x54mm)
Thrust Bearing x 2 (4x8x3.5mm)
Thrust Bearing Circlip x 2 (M4x6.5x1.5mm)
M2.5 Socket Head Screws x 2 (M2.5x6mm)
Washers x 2 (4x7.5x1mm)