Aircraft

Looking for the professional finish on your next quadcopter project? look no further! This simple and easy to install light module set, will not only provide you with a proffesional look but will also allow your quadcopter to be seen in any conditions with its super bright LEDs

The LED flash light set offers a wide voltage input range from 2-6s and is suitable for quadcopters up to 500mm diameter. 

Features:
• Suitable for quadcopters up to 500mm diameter
• Wide input voltage, 2-6s capability
• High efficiency frequency conversion circuit
• Low power consumption
• No flashing delay or brightness reduction
• High power output
• Simple frequency adjustment

Specs:
LED Cable Length: 500mm
System Weight: 48g
Input Voltage 7.4v ~ 22.2v

Protect your multirotor ESC / battery connectors from impact or prop damage with these handy
PCB's. Simply solder your Male XT90 connector directly to the board and secure to your multirotor
frame with some 3mm nuts and bolts.

Specs:
Length: 35mm
Width 10mm
Depth: 1.5mm
Hole Spacing: 35mm max

TF Model ESC and LED lighting power distribution board suitable for most quads and multi-rotors including SMACK TF250, OrcaTF280, TF650, TF680 and TF690.  A 3 position control channel can be setup to change the LED from Solid, Slow blinking and fast blinking LED lights.

Specs:
Dimensions: 50 x 50mm
Weight: 14g
ESC Output : 6
5V Output : 1
12V Output : 1
Mounting Holes : 45mm

Nylon Spacer 20mm M3 F/F Red (10pcs)

Specs:
Shape: Hex
Length: 20mm
Screw Thread: M3 Female/Female
Qty: 10 

Nylon Spacer 10mm M3 M/F Orange (10pcs)

Specs:
Shape: Hex
Length: 10mm
Screw Thread: M3 Male/Female
Qty: 10 

The Boom Stopper will help stop short circuits from blowing your electronics up. Simply plug in the Boom Stopper between the power source, usually your battery, and the components you are wanting to power for the first time. If there is a problem the inline 2A fuse will blow, instead of your components. When the fuse is blown the LED will light up indicating there is a short circuit and the Boom Stopper will reduce the current to a level that won't immediately damage your electronics, giving you time to remove the power supply. 

Lightweight Aluminium Round Section Spacer M3x38mm (Silver) (10pcs)

Lightweight aluminium spacers featuring a round cross section and a hex section (at each end) to fit a 5mm spanner. Ideal for use with helicopter and drone frames or similar applications where strong, accurate construction is required.

Specs:
Thread: M3
Length: 38mm
Weight: 1.5g each

The MultiStar Work Mat is a must have for any R/C hobbyist's work bench! Made from soft, grippy rubber and featuring ribbed compartments, it is perfect for containing small parts such as screws, nuts, washers and more. The backing is very grippy which will keep it from slipping on just about any surface. 

These smaller mats make excellent launch pads if you are taking off from uneven surfaces like grass or gravel.

The material is very soft and flexible allowing it to be easily rolled up for transport or storage. This makes it very easy to take with you to the race or field for on-site repairs. Never lose a screw again with the MultiStar Work Mat!

Features:
• Soft, grippy surface
• Ribbed compartments for containing small parts
• Flexible, can be rolled up for transport/storage

Specs:
Dimensions: 395 x 250mm

This latest addition to the XT60 range provides an integrated mount on the side of the XT60 with a 5mm mounting hole. This can be used to fix it to a drone frame (via a cable tie) or can be mounted to a frame stand-off. It could also be mounted to a battery tray in a plane or boat.