Aircraft

This is a great “bread board” pin ready accelerometer for your Arduino or other microcontroller projects

Features:
• BMA180 three-axis ultra-high performance digital accelerometer, which provides a 14-bit digital output via a 4-wire SPI or 2-wire I 2 C interface
• Full scale measurement range can be set to ± 1g balance, 1.5G, 2G, 3G, 4G, 8G or 16G
• programmable wake-up
• Low-g and high-g detection
• Tap detection
• Slope detection
• Self-test capability
• The sensor also has two operating modes: low noise, low power consumption in a tiny 3x3mm 12-pin LGA package BMA180
• The sensor can be between 1.62 to 3.6V VDD and 1.2 to 3.6V VDDIO supply will typically only consume 650uA standard mode.

Specs:
Size: 21 x 10 x 2.6mm
Voltage: 1.2-3.6v
Output: SPI or I2C

*Note: This is not an original Arduino brand product.

Superheterodyne 3310 Wireless receiver module +315RF Wireless transmitter module 

Arduino 6-DOF IMU Module Attitude Control 6DOF 3205 345

*Note: This is not an original Arduino brand product.

USBasp AVR Programming Device for ATMEL Processors

Includes:
1 x USBasp Device
1 x Cable

Suits the HobbyKing Quadcopter Control Board.

The X-CAM A10-3H Gimbal it at the top of the list when it comes to gimbals, the A10 has True continuous rotation 3-Axis ability with A/V Video link transfer. Full control over Roll, Tilt, Yaw, Mode and Zero home. And charging with A/V out transfer for the GoPro hero camera.

There are a lot of 3 Axis gimbals on the market, but only a few that use a slipper for true 360Deg continues rotation and also transfers the A/V output from the GoPro to the top controller for VTX use. The A/V line also powers/charges the GoPro. Another key feature on the X-CAM is its ability to go to zero or home using referencing sensors, this is great for when transitioning from a yaw control to a forward flight mode the gimbal will auto go to the front position.

The A10 uses an advanced method of vibration control and mounting and is a full CNC aluminum frame design with integrated motors for a light 280g weight.

If you’re serious about some aerial Photography with a GoPro this is the gimbal for you

Features:
• Continuous 360deg rotation
• A/V transfer cable with power
• 5 chs of adjustment over Sbus
• Sbus and PPM support
• Home sensors
• GUI and Upgrade ability
• Wide input voltage range
• Aluminum construction

Specs:
Weight:  280g ( without GOPRO )
Stabilization frequency:  5200Hz
Input voltage:  7.4v ~ 16.8v ( 2S ~ 4S Lipo )
Tilt travel:  +-90 degree; Roll travel:  +-45 degree
YAW travel:  360 degrees unlimited rotation

These custom made aluminum extrusions are perfect for you Multi-Rotor DIY projects, no more borrowing moms shower curtain rods...they have internal riffling (ribbing) added to remain ultra-light but have increased strength and anti-vibration characteristics as well as anodized for various color options for orientation and Bling.

Specs:
Diameter:12.8 x 12.8mm (.5inch)
Length: 600mm
Color: Black
weight: 55g

These custom made aluminum extrusions are perfect for you Multi-Rotor DIY projects, no more borrowing moms shower curtain rods...they have internal riffling (ribbing) added to remain ultra-light but have increased strength and anti-vibration characteristics as well as anodized for various color options for orientation and Bling.

Specs:
Diameter:15 x 15mm
Length: 600mm
Color: Black
weight:63g

2mm 2 Blade CNC Folding Propeller Adapter CW & CCW (Gold)

Perfect for multi-rotors, pack comes complete with M2.5 mounting screws for the folding propeller blades.

Specs:
Suits Motor Shafts: 2mm
Blade Thickness: 3mm
Blade Mounting: M2.5
Direction: 1 x Clockwise, 1 x Counterclockwise
Material: Aluminum
Color: Gold
Weight: 6g each

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3mm
Prop bolt dia: 2.5mm
Prop hole spacing: 18mm center to center
Dimensions: 25 x 8 x 9mm
Weight: 8g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3mm
Prop bolt dia: 2.5mm
Prop hole spacing: 18mm center to center
Dimensions: 25 x 8 x 9mm
Weight: 8g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 10g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3.17mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3.17mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3.17mm
Prop bolt dia: 2.5mm
Prop hole spacing: 18mm center to center
Dimensions: 25 x 8 x 9mm
Weight: 8g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3.17mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3.17mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 40g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3.17mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3.17mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 40g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3.17mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3.17mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 40g (Pair)

Ever wanted to know how fast your motor is spinning?
Wished you could better select the right propeller for your motor?
Now you can more accurately tune and performance test your engine, motor, edf or heli with the Turnigy tachometer.

Measures 2 to 9 propellers.
Super easy to use.
0-99999rpm range

Features:
Ultra sharp backlit LCD
220mah Lion battery included
Auto shut-off when idle. (no more flat batteries)
Weighs only 39g.

This handy little accessory will allow you to easily split a single receiver channel output into five. A handy accessory for those building multicopters as it gives you an easy way to program the throttle range into your ESC's all together prior to fitting them to your frame. It can also be used as a splitter in LED lighting systems.

Spec:
Lead length: 60mm
Weight: 3g

Mini black T Connector pack (5 Pairs)

Specs:
Base Dimensions: 5mm x 8mm
Contact Dimension: 3mm x 5mm x 1mm
Rating: 10amps continuous

Super flexible 26AWG twisted silicone male to male servo lead. These are specifically made as signal leads for RX to Flight controller connections, the light 26AWG silicone wire is so flexible it transfers virtually no vibration to the Flight controller, well the twist helps reduce inducted noise. If used in conjunction of having only one lead vertical and the other leads turned on their side for signal only, makes for a clean and minimal vibration transfer installation. Or better yet a single CPPM/SBUS single lead. 

Specs:
Length: 130mm(black/red/white)
Connection: Male JR style plug on each end.

Super flexible 26AWG twisted silicone male to male servo lead. These are specifically made as signal leads for RX to Flight controller connections, the light 26AWG silicone wire is so flexible it transfers virtually no vibration to the Flight controller, well the twist helps reduce inducted noise. If used in conjunction of having only one lead vertical and the leads turned on their side for signal only makes for a clean and minimal vibration transfer installation, or better yet a single CPPM/SBUS single lead.

Specs:
Length: 80mm(black/red/white)
Connection: Male JR style plug on each end.

A JST male plug to 2.54mm pitch male jumper lead for a variety of uses.

This lead is the best solution for batteries that are slightly out of balance; simply plug it into the individual cells on the balance lead, select a 1S charge rate and you can charge them one at a time to ensure they are all at optimum charge. 

Only use this method to restore cells that are slightly out of balance and remember that there could be something wrong with one of the cells so keep a close eye on it while charging.

Overall length: 70mm

The all-new Multistar twin output SBEC is an advanced switching DC-DC regulator designed specifically with multirotors in mind. It will simultaneously supply a constant 5Amps at 5V and 10Amps at 12V.

It works with 2-13 cell LiPo packs and supplies an interference-free constant 5V to your receiver and 12v to a gimbal, camera, or any other 12V accessory.

Always check the input voltage of any accessory before connecting the SBEC supply to it.
 
Specs:
Type: Switching
Input Protection: Reverse polarity protection
Output (Constant): 5v/5A and 12v/10A
Input: 6v-50v (2-13 cell LiPo) 
Dimensions: 60 x 25 x 17mm
Weight: 42g

Just because you may have outgrown your Legos and Erector sets does not mean the fun has to stop. Introducing RotorBits, the modular construction set of endless possibilities. Based on the idea of standardized connections and dimensions, the only limit to what can be built is your imagination.

RotorBits can be recycled and reused into other creations, mix and matching different bits to make a Y6 or Bi-Rotor! As your collection of Bits grows and concepts evolve with plug & play easy, who knows what you can come up with? Have club competitions for creative ideas or races for fastest box to air builds. RotorBits is one idea that can never be outdated only reconfigured.

RotorBits Anodized Aluminum Construction Profile 250mm (Gray)

Specs:
Size (LxW): 250 x 10mm
Weight: 28g
Color: Gray