Aircraft

The X-CAM A10-3H Gimbal it at the top of the list when it comes to gimbals, the A10 has True continuous rotation 3-Axis ability with A/V Video link transfer. Full control over Roll, Tilt, Yaw, Mode and Zero home. And charging with A/V out transfer for the GoPro hero camera.

There are a lot of 3 Axis gimbals on the market, but only a few that use a slipper for true 360Deg continues rotation and also transfers the A/V output from the GoPro to the top controller for VTX use. The A/V line also powers/charges the GoPro. Another key feature on the X-CAM is its ability to go to zero or home using referencing sensors, this is great for when transitioning from a yaw control to a forward flight mode the gimbal will auto go to the front position.

The A10 uses an advanced method of vibration control and mounting and is a full CNC aluminum frame design with integrated motors for a light 280g weight.

If you’re serious about some aerial Photography with a GoPro this is the gimbal for you

Features:
• Continuous 360deg rotation
• A/V transfer cable with power
• 5 chs of adjustment over Sbus
• Sbus and PPM support
• Home sensors
• GUI and Upgrade ability
• Wide input voltage range
• Aluminum construction

Specs:
Weight:  280g ( without GOPRO )
Stabilization frequency:  5200Hz
Input voltage:  7.4v ~ 16.8v ( 2S ~ 4S Lipo )
Tilt travel:  +-90 degree; Roll travel:  +-45 degree
YAW travel:  360 degrees unlimited rotation

These custom made aluminum extrusions are perfect for you Multi-Rotor DIY projects, no more borrowing moms shower curtain rods...they have internal riffling (ribbing) added to remain ultra-light but have increased strength and anti-vibration characteristics as well as anodized for various color options for orientation and Bling.

Specs:
Diameter:12.8 x 12.8mm (.5inch)
Length: 600mm
Color: Black
weight: 55g

These custom made aluminum extrusions are perfect for you Multi-Rotor DIY projects, no more borrowing moms shower curtain rods...they have internal riffling (ribbing) added to remain ultra-light but have increased strength and anti-vibration characteristics as well as anodized for various color options for orientation and Bling.

Specs:
Diameter:15 x 15mm
Length: 600mm
Color: Black
weight:63g

2mm 2 Blade CNC Folding Propeller Adapter CW & CCW (Gold)

Perfect for multi-rotors, pack comes complete with M2.5 mounting screws for the folding propeller blades.

Specs:
Suits Motor Shafts: 2mm
Blade Thickness: 3mm
Blade Mounting: M2.5
Direction: 1 x Clockwise, 1 x Counterclockwise
Material: Aluminum
Color: Gold
Weight: 6g each

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3mm
Prop bolt dia: 2.5mm
Prop hole spacing: 18mm center to center
Dimensions: 25 x 8 x 9mm
Weight: 8g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3mm
Prop bolt dia: 2.5mm
Prop hole spacing: 18mm center to center
Dimensions: 25 x 8 x 9mm
Weight: 8g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 10g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 10g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3.17mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3.17mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3.17mm
Prop bolt dia: 2.5mm
Prop hole spacing: 18mm center to center
Dimensions: 25 x 8 x 9mm
Weight: 8g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3.17mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3.17mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 40g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3.17mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3.17mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 40g (Pair)

These well made CNC aluminum adapters are designed to adapt folding propellers to motors with a standard 3.17mm shaft.

The Adapters can handle a range of blades from 5~12 inch props, and help make your Multirotor a little easier to transport, folding back towards the boom arms much like transporting an RC helicopter.

The adapters are secured to the motor shaft  by grub screws and they are suitable for any motors with a 3mm shaft.

Various colors are available to aid in rotation identification.

Grub screws and propeller mounting bolts included.

Specs:
Motor shaft dia: 3.17mm
Prop bolt dia: 2.5mm
Prop hole spacing: 22mm center to center
Dimensions: 29 x 8 x 9mm
Weight: 40g (Pair)

Ever wanted to know how fast your motor is spinning?
Wished you could better select the right propeller for your motor?
Now you can more accurately tune and performance test your engine, motor, edf or heli with the Turnigy tachometer.

Measures 2 to 9 propellers.
Super easy to use.
0-99999rpm range

Features:
Ultra sharp backlit LCD
220mah Lion battery included
Auto shut-off when idle. (no more flat batteries)
Weighs only 39g.

Replacement thumb screw for RJX CAOS 330

Includes
1x thumb screw

Propeller adapter for BE1806 motor 2 x CW

LDPOWER MT2206-1900KV Brushless Multicopter Motor (CW)

Innovators in multicopter technology, LDPOWER, have released their long awaited series of premium multicopter motors. These have been stringently tested to ensure outstanding performance, reliability and durability.

These motors are easy to install, very efficient and have no noise. They come in both CW and CCW formats.

LDPOWER motors are premium quality and will definitely answer the need of serious builders and flyers of quads/multis everywhere.

Specs:
KV(RPM/V): 1900KV
LiPoly cells: 7.4V-11.1V (2S-3S)
Max Power: 323.8W
Max Amps: 25.7A
Dimensions(Dia.xL): 29.5 x 27.7mm
Motor Shaft: 3mm
Prop shaft: 5mm
Weight: 34.7g
Bolt hole spacing: 19mm-M3*2  16mm-M3*2
Connectors: 2mm bullet

Volts  Prop   Throttle  Amps  Watts     RPM     Thrust (g)
7.4    6030   30%     1.8      13.32      8792      85
7.4    6030   50%     2.7      19.98    10341     123
7.4    6030   75%     3.9      28.86    11949     171
7.4    6030   100%    5.3      39.22    13656     228
7.4    6045   30%     2.5      18.5        7107     115.5
7.4    6045   50%     3.7      27.38     8607      164.5
7.4    6045   75%     6.0      44.4     10216      240
7.4    6045   100%    9.2     68.08    12003      335
11.1   6030   30%     3.1     34.41    12140      180
11.1   6030   50%     4.6     51.06    15621      249
11.1   6030   75%     6.9     76.59    16420      350
11.1   6030   100%    10.3   114.33   18953      480
11.1   6045   30%     3.8      42.18     9592      210
11.1   6045   50%     5.8      64.38   11258      292.5
11.1   6045   75%     10.1    112.11  13817      430.5
11.1   6045   100%    16.2    179.82  16315      594.5

This handy little accessory will allow you to easily split a single receiver channel output into five. A handy accessory for those building multicopters as it gives you an easy way to program the throttle range into your ESC's all together prior to fitting them to your frame. It can also be used as a splitter in LED lighting systems.

Spec:
Lead length: 60mm
Weight: 3g

Mini black T Connector pack (5 Pairs)

Specs:
Base Dimensions: 5mm x 8mm
Contact Dimension: 3mm x 5mm x 1mm
Rating: 10amps continuous

Super flexible 26AWG twisted silicone male to male servo lead. These are specifically made as signal leads for RX to Flight controller connections, the light 26AWG silicone wire is so flexible it transfers virtually no vibration to the Flight controller, well the twist helps reduce inducted noise. If used in conjunction of having only one lead vertical and the other leads turned on their side for signal only, makes for a clean and minimal vibration transfer installation. Or better yet a single CPPM/SBUS single lead. 

Specs:
Length: 130mm(black/red/white)
Connection: Male JR style plug on each end.

Super flexible 26AWG twisted silicone male to male servo lead. These are specifically made as signal leads for RX to Flight controller connections, the light 26AWG silicone wire is so flexible it transfers virtually no vibration to the Flight controller, well the twist helps reduce inducted noise. If used in conjunction of having only one lead vertical and the leads turned on their side for signal only makes for a clean and minimal vibration transfer installation, or better yet a single CPPM/SBUS single lead.

Specs:
Length: 80mm(black/red/white)
Connection: Male JR style plug on each end.

This data cable allows you to connect our 433/915MHz V1.1 Radio Telemetry Kits to your Walkera X800 GPS Quadcopter. The X800 flight controller has a data port which actually functions as a standard APM UART connection. The port is a specialized 4-pin connector which will not fit standard Molex style plugs.

This data cable will allow you to plug directly to the X800 FC data port and to our 433/915MHz V1.1 Radio Telemetry air module, allowing full access to wireless telemetry functionality of the APM based X800 flight controller.

Specs:
Connection: 4-pin Walkera style plug to 6-pin Molex style plug
Length: 180mm

*Note: Please see related items below for the compatible 433/915MHz V1.1 Radio Telemetry Kits.

A JST male plug to 2.54mm pitch male jumper lead for a variety of uses.

This lead is the best solution for batteries that are slightly out of balance; simply plug it into the individual cells on the balance lead, select a 1S charge rate and you can charge them one at a time to ensure they are all at optimum charge. 

Only use this method to restore cells that are slightly out of balance and remember that there could be something wrong with one of the cells so keep a close eye on it while charging.

Overall length: 70mm

The Vortex FPV Racer from ImmersionRC is an incredible piece of kit for the serious competitor, but like all things flying the ocassional mishap is inevitable!

This crash kit is a convenient way to keep a stock of all of those plastic parts most likely to be damaged in a serious "departure from controlled flight"

Included are all parts which mount the motors to the carbon fiber arms, the plastic pivot points, foldable arm clips, and all other plastic parts.

No carbon fiber parts are included (see Crash Kit 2.)

Included:
1 x Front bumper (FR4)
2 x Side plates
8 x Arm clips
4 x Arm pivot tops
4 x Arm pivot bottoms
4 x Landing bumpers
4 x Landing mounts
4 x Motor mounts
8 x Hex bushes
1 x Camera support base
1 x Camera support arm
4 x Damper pins
4x Damper circlip
4x Screw HA2x8
4x Screw HA2x6

Turnigy Talon Carbon Fiber Main Frame Upper Plate (1pc/bag)

Turnigy Talon Carbon Fiber Main Frame Lower Plate (1pc/bag)

HobbyKing X525 V3 Hardware Set (complete)

Anyone that flies the small 250 class quads has gone through a few props, whether you're trying to fit through something or had an acro mishap.  These prop guards will adapt to most 250 class frames via the motor mounting bolts. The guards will not only help save your props but help protect others and property from the high speed 5 inch props. 

Features:
• Adaptable to most frames
• Light weight and durable G10
• Protects your props and property 

Specs:
Size: For 5 inch props
Weight: 4.5g each
Mounting: Via motor mounting 12,16,19mm

Looking for the ultimate power system for your next Multi-rotor project? Look no further!

 The Turnigy Multistar outrunners are designed with one thing in mind - maximising Multi-rotor performance! They feature high-end 45SH magnets, high quality NMB bearings, 16 Poles, custom motor mount and all are precision balanced for smooth running, these motors are engineered specifically for multi-rotor use.

 The 4225-390 includes a prop adapter(6mm) and has a built in aluminium mount for quick and easy installation on your multi-rotor frame. These motors are supplied inside a nice foam lined Multistar metal box.

These Multistar outrunners have been specifically designed from the ground up for multi-rotor use and are not based on aeroplane motors.


Spec:
KV(RPM/V): 390
Lipo cells: 6s
Max Surge Watts(W): 330
Working current: 11 amps
Max.current(10s): 15 amps
No Load Current: 0.2 amps
Intemal Resistance: 0.24 ohm
Number of Poles: 16
Dimensions(Dia.xL): 42 x 24.5 mm
Shaft: 3 mm
Prop: 12 x 3 - 12 x 6
Weight: 86g

Looking for the ultimate power system for your next Multi-rotor project? Look no further!

The Turnigy Multistar outrunners are designed with one thing in mind - maximising Multi-rotor performance! They feature high-end 45SH magnets, high quality NMB bearings, 16 Poles, custom motor mount and all are precision balanced for smooth running, these motors are engineered specifically for multi-rotor use.

The 4225-610 includes a prop adapter(6mm) and has a built in aluminium mount for quick and easy installation on your multi-rotor frame. These motors are supplied inside a nice foam lined Multistar metal box.

These Multistar outrunners have been specifically designed from the ground up for multi-rotor use and are not based on aeroplane motors.


Spec:
KV(RPM/V): 610
Lipo cells: 4s
Max Surge Watts(W): 330
Working current: 16 amps
Max.current(10s): 22 amps
No Load Current: 0.3 amps
Intemal Resistance: 0.091 ohm
Number of Poles: 16
Dimensions(Dia.xL): 42 x 24.5 mm
Shaft: 3 mm
Prop: 12 x 3 - 12 x 6
Weight: 86g

This small lightweight 4ch switch is extremely handy for auxillary functions on all sorts of models. Plug the single lead into an auxillary switched function then switch your radio on, channel 1 on the electronic switch will then be active, cycle the auxillary switch once and channel 1 goes out and channel 2 comes on, cycle the switch once more and 2 goes out and channel 3 comes and so on until it comes back to channel 1. When the radio is switched off and then switched back on the unit will default to channel 1 each time. This unit is great for switching lights on and off and other low current applications.

Please note: For this switch to work correctly you will need to set the related channel travel to +- 100%.

Specs:
Input Voltage: 4.8~7.4v
Output Voltage: 4.8~7.4v
Maximum Current: 2amps
Length: 40mm
Width: 20mm
Height: 12mm
Weight: 7g
Input Cable: 21cm (JR type plug)

Quanum Exoskeleton for RunCam

Are you worried about your RunCam action camera not surviving a hard landing?  Simply give your RunCam a rigid exoskeleton frame.

Manufactured from super light weight alloy and machined to allow easy access to all of the RunCams many functions while maintaining a clear view from the lens, this frame gives you peace of mind when you send your favorite action camera into the thick of it!

Features:
• Purpose made to fit the RunCam Action Camera
• Tough, exoskeleton style design
• Superlight Alloy
• Access to all camera functions
• Bolt together case
• Lens shield

Specs:
Dimensions: 69 x 46 x 23mm
Weight: 21.5g

Are you looking to convert your SK450 quadcopter into a flying dead cat? If so, we have just the thing! This kit allows you to convert your standard SK450 into the "Dead Cat" style configuration with or without (your choice) the mess and hassle of mounting your own dead feline to the frame.

In addition to flying your deceased family pet around at home or your favorite local flying site, this configuration is also ideal for aerial video/photography as the front arms offer an extra wide field of view. The integrated camera mount plate located at the front of the frame is perfect for mounting a GoPRO or similar sized camera.

This kit includes everything necessary to convert your SK450 quad frame into either a wicked camera rig or a morbid dead pet mobile, the choice is yours!

*Note: This is a conversion kit only, the arms and other components are not included, it requires the use of original SK450 frame parts to complete.

Specs:
Front arm width: 490mm
Rear arm width: 375mm
Weight: 460g (completed frame w/out electronics)

Includes:
Lower main frame plate
Upper main frame plate
All necessary hardware

5.6mm x 18mm M3 Nylon Tapped Spacer (10pc).

Perfect for mounting Multi-rotor control boards.

Need to repair crash damage to a Multi-rotor flight board or add pin outs to any other electronics project?

These header pin blocks use the industry standard spacing of 2.54mm and are designed for soldering directly into printed circuit boards (PCB's). They are supplied in 30 pin lengths which can be easily cut to seperate individual pins.

There are 5 strips per pack.

Need to repair crash damage to a Multi-rotor flight board or add pin outs to any other electronics project?

These header pin blocks use the industry standard spacing of 2.54mm and are designed for soldering directly into printed circuit boards (PCB's). They are supplied in 30 pin lengths which can be easily cut to seperate individual pins.

There are 5 strips per pack.