Area di Liquidazione

Alimenti i vostri articoli elettrici compatibili con la HXT 4mm a convertitore DC jack. Il convertitore DC Jack è dotato di due connettori jack da 2 mm (centri positivi) ed è ideale per alimentare i caricabatterie o articoli elettrici simili.

Specifiche:
Lunghezza: 210mm
DC Jack: 2mm
Connettore batteria: HXT 4 millimetri

La maggior parte dei pacchi batteria al litio polimeri standard, 7S dispongono di due porte di equilibrio, un equilibrio di piombo 4S e 3S (totale 7S). Questo rende difficile caricare con la maggior parte caricabatterie standard che presentano una sola porta equilibrio.

Con questo adattatore super utile si può facilmente caricare la batteria 7S con qualsiasi caricabatteria saldo 8 ~ 10S capace standard che accetta spine equilibrio JST-XH. Questo adattatore prende le 4S e 3S singole spine dal tuo zaino, e li combina a un singolo plug equilibrio 7S, che è in grado di connettersi alla maggior parte degli standard di 8 ~ 10S caricatori capaci.

Specifiche:
Ingresso: 1 x 4S e spina equilibrio 1 x 3S JST-XH
Spina equilibrio 7S JST-XH: Uscita
Lunghezza: 100mm

HXT 4mm a T-connettore dell'adattatore Cavo batteria (2pc)

Questo adattatore permette di convertire una batteria HXT 4 millimetri dotato di un connettore a T per l'uso con un ESC attrezzata T-connettore o piombo carica.

Spec:
Peso: 7g (ciascuno)

Utilizzare questo adattatore per convertire un cavo di carica XT-60 per la ricarica delle batterie JST attrezzata.

This simple and effective charge lead comes pre-soldered with standard 4mm bullet connectors at the charger end and has stepped, bullet connectors at the battery end allowing you to charge hard case packs that utilise 4mm and 5mm connectors. 

This adapter will convert an HXT 5.5mm bullet equipped battery to an XT90 for use with an XT90 equipped ESC or an XT90 Charge lead.

This adapter will convert an XT90 equipped battery to an HXT 5.5mm bullet for use with an HXT 5.5mm bullet equipped ESC or an HXT 5.5mm bullet Charge lead.

XT30U Silicone Charge Lead with 4mm Banana Plugs.

An excellent, low resistance, flexible silicone charge lead with standard 4mm banana plugs on one end and a set of XT150/AS150 on the other. The Amass XT150/AS150 is a 7mm anti-spark connector rated at up to 150amps, and the 4mm banana plugs suits most chargers on the market today.

Specs:
Battery Connector: XT150/AS150 (7mm)
Charger Connection: 4mm Banana Plug
Wire Diameter: 14AWG
Wire: Tinned copper
Wire Insulation: Silicone rubber
Length: 300mm
Weight: 37.3g

Designed in-house by HobbyKing, this Turnigy parallel charge board can charge up to 6 LiPo or LiHV packs of the same capacity and cell count at the same time. The board is supplied with TRA connectors for the main charging leads, an XT60 lead to plug into the charger, and 2~6S JST-XH connectors for the balancing leads. The board is fused for protection and a 6S JST-XH adaptor lead is also supplied to connect the board to your charger balancing input.

Designed in-house by HobbyKing, this Turnigy parallel charge board can charge up to 6 LiPo or LiHV packs of the same capacity and cell count at the same time. The board is supplied with EC3 connectors for the main charging leads, an XT60 lead to plug into the charger, and 2~6S JST-XH connectors for the balancing leads. The board is fused for protection and a 6S JST-XH adaptor lead is also supplied to connect the board to your charger balancing input.

Designed in-house by HobbyKing, this Turnigy parallel charge board can charge up to 6 LiPo or LiHV packs of the same capacity and cell count at the same time. The board is supplied with EC5 connectors for the main charging leads, an XT60 lead to plug into the charger, and 2~6S JST-XH connectors for the balancing leads. The board is fused for protection and a 6S JST-XH adaptor lead is also supplied to connect the board to your charger balancing input.

Designed in-house by HobbyKing, this Turnigy parallel charge board can charge up to 6 LiPo or LiHV packs of the same capacity and cell count at the same time. The board is supplied with TR connectors for the main charging leads, a pair of 4mm banana plugs to connect to the charger, and 2~6S JST-XH connectors for the balancing leads. The board is fused for protection and a 6S JST-XH adaptor lead is also supplied to connect the board to your charger balancing input.

Designed in-house by HobbyKing, this Turnigy parallel charge board can charge up to 6 LiPo or LiHV packs of the same capacity and cell count at the same time. The board is supplied with EC3 connectors for the main charging leads, a pair of 4mm banana plugs to connect to the charger, and 2~6S JST-XH connectors for the balancing leads. The board is fused for protection and a 6S JST-XH adaptor lead is also supplied to connect the board to your charger balancing input.

Il cavo adattatore ToolkitRC SC100 viene utilizzato per alimentare caricabatterie a basso wattaggio o altri dispositivi con un connettore di ingresso XT60 da un alimentatore USB-C fino a 100 W.

Specifiche:
Tipo: ToolkitRC SC100 XT60~Cavo protocollo USB-C
Ingresso: USB-C 5.0~20V@PD2.0/PD3.0/QC2.0
Tensione di uscita: 5~20V max
Corrente di uscita: 5 A max
Connettore di uscita: XT60
Lunghezza: 50 cm
Peso: 35 g