Uitverkoopgebied

The Turnigy TrackStar range of 1/10th Brushed Motors is ideal for those that require a no-nonsense motor that will power your vehicle in any conditions. These motors are an ideal solution for backyard bashers or anyone wanting to cross rivers or travel in a wet environment.

The Turnigy TrackStar range of 1/10th Brushed Motors is ideal for those that require a no-nonsense motor that will power your vehicle in any conditions. These motors are an ideal solution for backyard bashers or anyone wanting to cross rivers or travel in a wet environment.

The AeroStar WiFi Connect offers an easier way to program an AeroStar WiFi electronic speed controller (ESC). This controller connects to your ESC via your Android phone or iOS device using WIFI to make it simple to configure and monitor your ESC.

For Android users you need to use this link and download the Android APK: https://drive.google.com/file/d/1Tkev-d0ggqEVN9QZy86MJ4tL8nVJDWdv/view

For iOS users you will need to download it via the Apple Store, APP name: Flycolor Configurator

This kit comes complete with the FrSky Taranis X-Lite BRACE. There are also red replacement gimbal stick ends in two sizes, short and long, depending on your needs.

The QUICRUN 880 Dual ESC is a durable, highly reliable waterproof electronic speed controller that has been designed for twin brushed motors in 1/10 and 1/8th scale vehicles. The HobbyWing patented copper heat conductive plates attached to the MOSFET board allows the internal heat to be quickly transferred to the aluminum heatsink for faster and greater heat dissipation.

Als je je zorgen maakt over krassen op het scherm van de Evolution PRO's of beschadiging van een stuurknuppel tijdens het transport, dan voldoet deze hoes aan al je eisen. Hij klikt eenvoudig op de voorkant van je controller om het scherm veilig te bewaken en blijft plakken. Het komt in zwart of wit.

Als je je zorgen maakt over krassen op het scherm van de Evolution PRO's of beschadiging van een stuurknuppel tijdens het transport, dan voldoet deze hoes aan al je eisen. Hij klikt eenvoudig op de voorkant van je controller om het scherm veilig te bewaken en blijft plakken. Het komt in zwart of wit.

High gain, high sensitivity RF components are used throughout, this coupled with FLYSKY's latest generation intelligent wireless 2.4GHz AFHDS 3 protocol, enables the receiver to reject interference easily, while maintaining high reception rates, and stable performance. This version 2 FGr4 supports PPM, i-BUS, and 4 PWM data outputs (CH1~CH4), and an input for connecting additional sensors. Another feature of this quality FLYSKY receiver is the ability to handle a wide input voltage, anything from 3.5-12V can be used, and the case has a sealing gasket which makes it water-resistant.

This SH Engines R5 (Medium Cold) glow plug is perfect for .12~.36 size engines using 16~36% nitro fuels.

The FGr8B surface micro receiver adopts FLYSKY's third-generation automatic frequency hopping digital system (AFHDS 3), it is perfectly suited to their range of PL18, NB4, and NB4 Lite transmitters. It uses a single antenna bidirectional transmission system that is uniquely designed to install and output PWM/PPM, and iBUS in signals.

A replacement 3720-900KV brushless motor with prop shaft for the H-King MX2 Extreme 30E.

The FTM302 adopts FLYSKY's third-generation automatic frequency hopping digital system, AFHDS 3. It uses a single antenna, a bidirectional transmission system in a compact design with support for multiple signal inputs. Supports external power and is compatible with standard JR-type module bays.

The FTM302 offers a long range of up to 3.5km + on the EU default setting of 20dBm (changeable through the management system), low latency, less than 10ms, and allows for online updates and managing the module via the FLYSKY Remote Control Assistant. Power to the module can either be internal, or an external power source of 5~28V can be connected via the built-in XT30 connector. The module also has a built-in fan which automatically turns on if the temperature reaches 45°C to ensure the system remains safe, this can happen when the module is being used with higher voltages.

Wil je nog meer snelheid en kracht voor je H-King Reno Aces P-51 "Galloping Ghost"? Upgrade dan naar deze optionele krachtige Pro 3108-1160KV brushless en verander hem in een ballistische raket met onbeperkte verticale prestaties. Het is niet nodig om de meegeleverde propeller of ESC te veranderen, beide zijn prima met deze upgrade.

A strong, flexible, transparent fuel tank that is suitable for most types of RC models. The fuel tank includes a machined metal cap with fuel feed, a flexible fuel feed pipe with clunk weight, and 2 factory-installed machined metal 90° hose attachment nipples. One of these is for filling the tank, and the other is used for pressure or venting. Each fuel tank comes with a Turnigy sticker that includes the capacity of the tank, this can be attached to the tank in a convenient position to remind you of its size. The fuel tank is suitable for use with both gas and nitro fuels.

A replacement crankshaft set for the Turnigy TP10 10cc gas engine. This set includes the crankshaft, conrod, prop-driver woodruff key, and prop nut.

A replacement crankcase set for the Turnigy TP10 10cc gas engine, this set includes the crankcase, gasket, and 2 x screws.

A replacement prop driver set for the Turnigy TP10 10cc gas engine. This set includes the prop driver with inset magnet, prop washer, and woodruff key.

A replacement crankcase for the Turnigy TP26 26cc gas engine.

Accurately drill your propellers for your TP 35cc gas engine with this easy-to-use drilling jig. The jig is CNC machined from aluminum stock and is supplied with a clamping screw to hold the propeller secure whilst drilling.

A replacement 4S 50mm 12 blade ducted fan unit with brushless motor for the H-King F-16 Fighting Falcon 550mm.

The Aerostar RVS G2 next-generation range of HV Opto brushless speed controllers moves these amazing ESCs up a notch from the ground-breaking original Aerostar RVS HV ESCs. New generation MOSFETs with the aid of the highly efficient cooling fan and finned, aluminum heatsink, ensure that the ESC stays within operating temperatures at all times, and can also safely handle the peak current draw specified. They process much faster due to the high-performance 32bit M4 microprocessor running at 170MHz, and have improved functionality and programmable features. Our RVS (reverse function system) is now instantaneous, with no need for the motor to stop turning, this makes it perfect for EDF braking (reverse thrust), and waterplanes for taxiing, etc. If you don't require the reverse function, simply do not connect the second lead to your receiver, it will then operate as a standard ESC.

The RadioMaster RP V2 series of receivers now have a built-in TCXO (Temperature-Compensated Xtal Oscillator). The TCXO ensures high stability and accuracy in frequency control and compensates for temperature variations. This results in consistent and reliable signal reception, even in extreme temperature conditions. It also reduces frequency drift over time, providing long-term frequency stability and preventing signal degradation. This provides a superior performance in demanding environments and enhances the flight experiences.

The RP2 2.4GHz ELRS Nano receivers use the high-performance, revolutionary ExpressLRS open-source system. The Nano receivers were designed by the ExpressLRS development team, and feature the ESP8285 MCU and SX1280 RF chips. WiFi is built-in so that you can easily upgrade the firmware and configure the receiver using your PC or mobile phone. Other features of the RP2 V2 are improved solder pads and a super lightweight built-in ceramic antenna.

The RP3 2.4GHz ELRS Nano receivers use the high-performance, revolutionary ExpressLRS open-source system. The ExpressLRS development team designed the Nano receivers, which feature the ESP8285 MCU and SX1280 RF chips. This offers Lora and FLRC 2.4GHz RF links for incredible range and low latency. WiFi is built-in to easily upgrade the firmware and configure the receiver using your PC or mobile phone.

The receiver features a Skyworks SE2431L providing an LNA for improved receiver performance, a PA providing up to 100mW of telemetry performance, and antenna switching for antenna diversity.. The RP3 Nano receiver is available in either an FCC or a European LBT version, please check the specifications below for the supported protocol.

This optional EDF nacelle unit will convert your XFLY Swift 2100 into an EDF-powered sport glider. The unit includes the XFLY Galaxy 64mm 12-blade fan, and the powerful XFLY 2840-3200KV brushless motor to give your Swift on a 4S battery an incredible performance. Installation is very straightforward, once installed you will only need to remove the prop and fit the supplied nose cone.

Specs:
Type: XFLY Swift 2100 Sport Glider Optional EDF Unit
Fan: 64mm 12-blade
Motor: 2840-3200KV brushless
Thrust: 1250g
Recommended Battery: 14.8V (4S) 2200~3300mAh LiPo (not supplied)

The Rhino VE40A electronic speed controller with 32-bit MCU has been designed primarily for competitive 1/10, and 1/12 RC rock crawlers, but it is also very suitable for other types of cars and trucks. The preloaded AM32 custom firmware is optimized for RC rock crawlers, but the firmware can be configured for other applications by using the DYS USB-Link (not supplied).

This Bluetooth module makes the programming of your Aerostar RVS G2 HV electronic speed controller extremely easy, simply download the Aerostar App to your Android smartphone or smart device and you are ready to connect and set up your ESC (see under the "Files" tab for the link to the App).

Programmable settings using the Bluetooth module:
• Brake Type: Off/Soft/Mid/Hard
• Motor Timing: Auto/High/Mid/Low
• Motor Rotation: CW/CCW
• HEF (High Efficiency Function: On/Off
• Cell Count (HV Version): Auto/6S/8S/10S/12S/14S
• LVC (Low Voltage Cut-Off/HV): Off/2.3V/2.5V/3V/3.2V/3.2V/3.4V/3.6V
• Voltage Cut-Off Type: Reduce Power/Cut-Off Power
• Start-Up Power: Low/Med/Hard
• Restore Factory Defaults

The G2 HV factory defaults are shown in "Bold".

Please note: This Bluetooth module is only compatible with the Aerostar RVS G2 HV ESC range. It is incompatible with the non-HV series of G2 ESCs, earlier versions of the Aerostar RVS HV ESC, or the ZTW brand of ESC..

The Rocket Surpass range of brushless motors is precision-made using the latest manufacturing processes. The heatsink can is CNC machined from a solid billet of 6061 T6 aluminum, high-purity copper is used for the windings for improved efficiency, and oversized bearings are used for durability. The stator has super thin (0.2mm) laminations, and the rotor is then precision balanced for reliability, and ultra-smooth running at maximum RPMs.

The Rocket Surpass range of brushless motors is precision-made using the latest manufacturing processes. The heatsink can is CNC machined from a solid billet of 6061 T6 aluminum, high-purity copper is used for the windings for improved efficiency, and oversized bearings are used for durability. The stator has super thin (0.2mm) laminations, and the rotor is then precision balanced for reliability, and ultra-smooth running at maximum RPMs.

The Rocket Surpass 4076-2025KV motor has been specially built for 1/8th scale monster trucks and truggies. This 4-pole, 12-slot high-torque motor is water and dust-proof and features a universal mounting system to fit just about all 1/8th-scale vehicles.

The Rocket Surpass range of brushless motors is precision-made using the latest manufacturing processes. The heatsink can is CNC machined from a solid billet of 6061 T6 aluminum, high-purity copper is used for the windings for improved efficiency, and double-shielded oversized bearings are used for durability. The motor includes sintered neodymium magnets, the stator has super thin (0.2mm) laminations, and the rotor is precision balanced for reliability, and ultra-smooth running at maximum RPMs.

The Rocket Surpass 5065-236KV motor suits sport, scale, and 3D-type models. This robust motor suits LiPo batteries up to 10S, on test with a 10S battery it produced an incredible 2000 watts of power at 57A, making it a great motor for the larger models. The motor is supplied with a machined prop adapter, complete with mounting bolts, allowing it to be mounted either way round.

This high-quality all-metal fan unit uses the latest technology and high-grade aluminum alloy to ensure a powerful, smooth-running unit. It is built to the highest of standards, and each blade is precision made to generate the best airflow, and to a rigorous 8-hour fatigue test before installation.

The highly rigid structure is capable of running at a very high RPM which produces an extremely high efflux velocity for maximum speed and efficiency. The design includes an anti-disintegrating safety feature that will stop a blade from flying out of the shroud in the unlikely case of failure. The shroud itself acts as a heatsink for the motor and each unit has been dynamically balanced to ensure smooth running and a long lifespan for both the fan unit and the motor.

The Rocket Surpass range of brushless motors is precision-made using the latest manufacturing processes. The heatsink can is CNC machined from a solid billet of 6061 T6 aluminum, high-purity copper is used for the windings for improved efficiency, and oversized ABEC5 high-speed bearings are used for durability. The stator has super thin (0.35mm) laminations, and the rotor is then precision balanced for reliability and ultra-smooth running at maximum RPMs.

The Rocket Surpass KK2845-5900KV motor has been specially built for 1/12~14th size RC cars and trucks and is totally waterproof for use in extreme conditions. This powerful 4-pole, 12-slot motor features a universal mounting system so that it will fit just about all 1/12~14th scale vehicles.

The Rocket Surpass range of brushless motors is precision-made using the latest manufacturing processes. The heatsink can is CNC machined from a solid billet of 6061 T6 aluminum, high-purity copper is used for the windings for improved efficiency, and oversized ABEC5 high-speed bearings are used for durability. The stator has super thin (0.35mm) laminations, and the rotor is then precision balanced for reliability and ultra-smooth running at maximum RPMs.

The Rocket Surpass 3650-5400KV motor has been specially built for 1/10th size RC cars and trucks and is water and dust-resistant for use in demanding conditions. This powerful 4-pole, 12-slot motor features a universal mounting system so that it will fit just about all 1/10th scale vehicles.

The Rocket Surpass range of brushless motors is precision-made using the latest manufacturing processes. The heatsink can is CNC machined from a solid billet of 6061 T6 aluminum, high-purity copper is used for the windings for improved efficiency, and oversized ABEC5 high-speed bearings are used for durability. The stator has super thin (0.35mm) laminations, and the rotor is then precision balanced for reliability and ultra-smooth running at maximum RPMs.

The Rocket Surpass 3660-4500KV motor has been specially built for 1/10th size RC cars and trucks and is water and dust-resistant for use in demanding conditions. This powerful 3T, 4-pole, 12-slot motor features a universal mounting system so that it will fit just about all 1/10th scale vehicles.