Uitverkoopgebied

Turnigy high quality silicone wire is ideal for your RC project. It is super flexible and soft with a high strand count which means it is great for use in restrictive and compact areas. Available in a wide variety of gauges and colors to suit just about any application. 

Now you can increase the fun with your BSR Berserker with this simple to install wheelie bar set. Includes ball-raced wheels, carbon fixing plates and wheel support cradle.

Now you can increase the fun with your BSR Berserker with this simple to install wheelie bar set. Includes ball-raced wheels, carbon fixing plates and wheel support cradle.

NGH GF30 30cc Gas 4 Stroke Engine Replacement Camshaft Cover Plate.

NGH GF30 30cc Gas 4 Stroke Engine Replacement Tappet Housing.

Excellent Quality Nylon Spinner with Lightened Alloy Backplate 38mm Red - Mount hole 5mm

This simple and effective charge lead comes pre-soldered with standard 4mm bullet connectors at the charger end and has stepped, bullet connectors at the battery end allowing you to charge hard case packs that utilise 4mm and 5mm connectors. 

Most people know ABS for its use as a filament for 3D Printing. HobbyKing is stocking ABS rods and tubes for use with model building. They can be used for architectural modeling, train scenery, wargamers and other dioramas. The uses are endless. The rods and tubes come in a variety of sizes. ABS is easy to work with and can be cut, sanded and glued.

Use these female JST-SH with your flight controller, VTX, cameras, and more. These picoblade-compatible pins can repair cables or help you make your own.

Use these female JST-SH with your flight controller, VTX, cameras and more. These picoblade-compatible pins can repair cables or help you make your own.

Front Sway Bar Set (silver/blue/black) - Basher SaberTooth 1/8 Scale Truggy / Nitro  Circus MT 

Rear sway bar set (silver/blue/black) - Basher SaberTooth 1/8 Scale Truggy

This receiver was specifically designed by OrangeRx with the FPV racer in mind. Although it is small and ultra-lightweight it has true diversity technology which is especially important for the harsh environment of FPV racing. These racing conditions are far from ideal, low altitude, lots of obstacles, motors, and video transmissions in close quarters, situations where you need a robust reception.

High Temperature Polyimide Tape has a high resistance to temperature extremes. Kapton tape is recommended for masking circuit boards and splicing wires. Made with polyimide film and silicone adhesive the tape can be easily released.

This handy programming box for the OrangeRx R620X to R1220X V3 and RR12RDTS receivers is perfect to have in your toolbox at the flying field in case you want to change the settings without the need for a PC. It has an integrated RF module that allows you to set up the receiver wirelessly or you can use a wired connection. As the RR12RDTS is primarily designed for drones and helicopters this programming box can also be used to adjust the settings of the flight stabilization systems.

These are Micro Engineerings HO/N scale Code 70 to 55 slide on plastic insulating rail joiners. These insulating joiners are perfect for where you want to electrically isolate sections of track when transitioning from Code 70 to Code 55 rail.

Micro Engineering produces a range of building structure components to allow you to construct your own scratch built buildings. These are double baggage doors that are suitable for warehouses and other storage lineside buildings etc.

Micro Engineering produces a range of building structure components to allow you to construct your own scratch built buildings. These office windows/doors are typical of the style used in office blocks around the world. They have many other uses as well so can be used in a variety of buildings that may appear on a model railway.

Micro Engineering produces a range of building structure components to allow you to construct your own scratch built buildings. This is a selection of typical roof vents and fans that you would see on buildings all around the world. Add that bit of realism to your scratch built buildings with these protypical fittings.

Micro Engineering produces a range of building structure components to allow you to construct your own scratch built buildings. Around railway, industrial buildings and garage scenes there always old car tires hanging around cluttering up the place . Add that little bit of realism to your model railway layout with these very effective tire stacks and loose tires.

This adapter will convert an HXT 5.5mm bullet equipped battery to an XT90 for use with an XT90 equipped ESC or an XT90 Charge lead.

This adapter will convert an XT90 equipped battery to an HXT 5.5mm bullet for use with an HXT 5.5mm bullet equipped ESC or an HXT 5.5mm bullet Charge lead.

Use this adapter lead to charge batteries with 4MM Bullet Connector plugs, even those with reversed polarity Connectors using the supplied adaptors.

Designed to be splash-proof, the HK-GT2 receiver is a great choice for boats, cars on muddy terrain and rainy days. Stop changing receivers from model to model and get an extra receiver now.

The Turnigy TrackStar range of 1/10th Brushed Motors is ideal for those that require a no-nonsense motor that will power your vehicle in any conditions. These motors are an ideal solution for backyard bashers or anyone wanting to cross rivers or travel in a wet environment.

The Turnigy TrackStar range of 1/10th Brushed Motors is ideal for those that require a no-nonsense motor that will power your vehicle in any conditions. These motors are an ideal solution for backyard bashers or anyone wanting to cross rivers or travel in a wet environment.

The Turnigy TrackStar range of 1/10th Brushed Motors is ideal for those that require a no-nonsense motor that will power your vehicle in any conditions. These motors are an ideal solution for backyard bashers or anyone wanting to cross rivers or travel in a wet environment.

The AeroStar WiFi Connect offers an easier way to program an AeroStar WiFi electronic speed controller (ESC). This controller connects to your ESC via your Android phone or iOS device using WIFI to make it simple to configure and monitor your ESC.

For Android users you need to use this link and download the Android APK: https://drive.google.com/file/d/1Tkev-d0ggqEVN9QZy86MJ4tL8nVJDWdv/view

For iOS users you will need to download it via the Apple Store, APP name: Flycolor Configurator

Aluminium Rear Bumper Type A - OH35A01 for the 1/35 Rock Crawler.

PGYTECH Lens filters can make all the difference to the quality of the video or pictures that the MAVIC PRO takes. These exceptional filters easily screw onto the camera lens.

This kit comes complete with the FrSky Taranis X-Lite BRACE. There are also red replacement gimbal stick ends in two sizes, short and long, depending on your needs.

This bearing detergent is the perfect partner to Mini Vibrating Cleaning Unit. Mix this detergent with water for removing grease, dust and other contaminants from bearings, gears, watch parts, jewelry and lots of other small intricate parts.

A simple device that protects the sticks of your DJI Mavic 2 transmitter when being travelling in it's case. Made of tough ABS and finished in a two tone gray that matches the Mavic 2.

This lens hood for the Mavic 2 very effectively suppresses lens flare, stray light entering the lens and also protects the gimbal from accidental damage. The "U" shaped design with extended shade minimizes vignetting (reduction of an image's brightness or saturation) and undesired color effects. The lens hood is made of high quality tough ABS plastic for durability and is supplied in a gray color that compliments the drone itself. The lens hood is quick and easy to install due to the quick mount design.

There is nothing like the sound of a 12 blade EDF. These are made from strong composite materials.