全ての受信機

This receiver was specifically designed by OrangeRx with the FPV racer in mind. Although it is small and ultra-lightweight it has true diversity technology which is especially important for the harsh environment of FPV racing. These racing conditions are far from ideal, low altitude, lots of obstacles, motors, and video transmissions in close quarters, situations where you need a robust reception.

This handy programming box for the OrangeRx R620X to R1220X V3 and RR12RDTS receivers is perfect to have in your toolbox at the flying field in case you want to change the settings without the need for a PC. It has an integrated RF module that allows you to set up the receiver wirelessly or you can use a wired connection. As the RR12RDTS is primarily designed for drones and helicopters this programming box can also be used to adjust the settings of the flight stabilization systems.

The FrSky RX8R has been upgraded to the PRO version but retains all the old features. The new PRO version has increased precision and lower latency. Its deviation of PWM is reduced to 0.5us, and the delay of PWM output is 9ms less than that of the X8R in high-speed mode. It also has improved anti-interference from the ignition system on combustion engines.

The Turnigy GT5 receiver is perfectly matched to work with the outstanding Turnigy GT5 6CH 2.4GHz AFHDS 2A Surface Radio to provide the most reliable link. Stop changing receivers from model to model and get an extra receiver now.

Designed to be splash-proof, the HK-GT2 receiver is a great choice for boats, cars on muddy terrain and rainy days. Stop changing receivers from model to model and get an extra receiver now.

FLYSKY FGR4Sレシーバーは、新しいAFHDS3プロトコル（第3世代自動周波数ホッピングデジタルシステム）を使用しています。 双方向伝送用に内部シングルアンテナを使用し、コンパクトなサイズで設置が簡単です。 標準のPPMおよびi-BUS信号を出力できます。 それはあなたのFLYSKYノーブルNB4表面ラジオに素晴らしい追加をします。

The FrSky TW R8 is an 8-channel, dual 2.4GHz frequency receiver with SBUS/FBUS/S.Port, and 8 PWM channels. These TWIN series receivers feature a stable TW protocol that benefits from simultaneously integrating dual active 2.4GHz frequency bands. The TW active-active protocol is different from the general active-standby redundancy solutions used by other manufacturers. This is where one receiver takes over signal control only when the other goes into failsafe mode. With the TW protocol, the dual/twin 2.4GHz frequency bands on the TW series receiver are active all the time.

The FrSky TW R6 is a 6-channel, dual 2.4GHz frequency receiver with SBUS/FBUS/S.Port, and 6 PWM channels. These TWIN series receivers feature a stable TW protocol that benefits from simultaneously integrating dual active 2.4GHz frequency bands. The TW active-active protocol is different from the general active-standby redundancy solutions used by other manufacturers. This is where one receiver takes over signal control only when the other goes into failsafe mode. With the TW protocol, the dual/twin 2.4GHz frequency bands on the TW series receiver are active all the time.

High gain, high sensitivity RF components are used throughout, this coupled with FLYSKY's latest generation intelligent wireless 2.4GHz AFHDS 3 protocol, enables the receiver to reject interference easily, while maintaining high reception rates, and stable performance. This version 2 FGr4 supports PPM, i-BUS, and 4 PWM data outputs (CH1~CH4), and an input for connecting additional sensors. Another feature of this quality FLYSKY receiver is the ability to handle a wide input voltage, anything from 3.5-12V can be used, and the case has a sealing gasket which makes it water-resistant.

The FGr8B surface micro receiver adopts FLYSKY's third-generation automatic frequency hopping digital system (AFHDS 3), it is perfectly suited to their range of PL18, NB4, and NB4 Lite transmitters. It uses a single antenna bidirectional transmission system that is uniquely designed to install and output PWM/PPM, and iBUS in signals.

The FTr10 adopts FLYSKY's third-generation automatic frequency hopping digital system, AFHDS 3. It uses a double-antenna, bidirectional transmission system to save space and supports standard PPM, S-Bus, and i-Bus signals.

The FTr10 is a small, lightweight 2.4GHz receiver that will accept a wide input voltage of between 3.5~18V, has an incredible range in interference-free open areas of up to 10km, and its unique design includes i-BUS, S-BUS, PPM, PWM, and UART data ports. It has the ability to update firmware online and is compatible with the FLYSKY Paladin PL18 radio system. With all these features it is the perfect choice for drone flying, drone racing, FPV, and other long-range applications.

The FTr4 adopts FLYSKY's third-generation automatic frequency hopping digital system, AFHDS 3. It uses a single antenna, bidirectional transmission system to save space and supports standard PPM, S-Bus, and i-Bus signals.

The FTr4 is a small, lightweight 2.4GHz receiver that will accept an input voltage of between 3.5~8.4V, has a range in interference-free open areas of up to 500m, and its unique design includes i-BUS, S-BUS, PPM, and PWM data ports. It has the ability to update firmware online and is compatible with the FLYSKY Paladin PL18, and NB4 radio systems. With all these features it is the perfect choice for drone flying, gliding, and small fixed-wing aircraft.

The Archer line of receivers has been enhanced further with the Plus Series, they include some exciting new features. Firstly an enhanced anti-RF-Interference capability can offer a more solid RF performance, they also feature ACCESS and ACCST D16 modes where the RF protocol is smart matched during the binding process. Another feature is a Black-Box function, which records basic flight details such as power and signal-related data.

The FrSky Plus SR8 receiver is designed for use in RC airplanes, it works as a traditional 8-Channel PWM Rx, but it also has a built-in 3-axis gyro and a 3-axis accelerometer sensor module. With the built-in sensors, the Plus SR8 will compensate for outside forces on the airplane and will enhance the stability making it easier and smoother to fly. The Plus SR8 supports multiple flight modes, Auto-level, Stabilisation, Hover, and Knife-Edge. Also available are several configuration methods, these include LUA, or the FrSky S.port Airlink+ combined with the Freelink App.

The ER6G receiver has been specially designed for glider pilots who require a compact and slim receiver. It can drive up to 6 servos and has built-in receiver voltage telemetry and flight battery telemetry with the ability to automatically detect which voltage input to use. The ER6G features a dual-antenna with telemetry power up to 50mw and works quite happily with a 1S Lipo receiver battery.

The ER6G receiver has been specially designed for glider pilots who require a compact and slim receiver. It can drive up to 6 servos and has built-in receiver voltage telemetry and flight battery telemetry with the ability to automatically detect which voltage input to use. The ER6G features a dual-antenna with telemetry power up to 50mw and works quite happily with a 1S Lipo receiver battery.

The ER6GV receiver has been specially designed for glider pilots who require a compact and slim receiver with a built-in high-precision air pressure vario. It can drive up to 6 servos and has built-in receiver voltage telemetry and flight battery telemetry with the ability to automatically detect which voltage input to use. The ER6G features a dual-antenna with telemetry power of up to 50mw and works quite happily with a 1S Lipo receiver battery.

The ER6GV receiver has been specially designed for glider pilots who require a compact and slim receiver with a built-in high-precision air pressure vario. It can drive up to 6 servos and has built-in receiver voltage telemetry and flight battery telemetry with the ability to automatically detect which voltage input to use. The ER6G features a dual-antenna with telemetry power of up to 50mw and works quite happily with a 1S Lipo receiver battery.

The ER8G receiver has been specially designed for glider pilots who require a compact and slim receiver. It can drive up to 8 servos and has built-in receiver voltage telemetry and flight battery telemetry with the ability to automatically detect which voltage input to use. The ER8G features a dual-antenna with telemetry power up to 100mw and works quite happily with a 1S Lipo receiver battery.

The ER8G receiver has been specially designed for glider pilots who require a compact and slim receiver. It can drive up to 8 servos and has built-in receiver voltage telemetry and flight battery telemetry with the ability to automatically detect which voltage input to use. The ER8G features a dual-antenna with telemetry power of up to 100mw and works quite happily with a 1S Lipo receiver battery.

The ER8GV receiver has been specially designed for glider pilots who require a compact and slim receiver with a built-in high-precision air pressure vario. It can drive up to 8 servos and has built-in receiver voltage telemetry and flight battery telemetry with the ability to automatically detect which voltage input to use. The ER8GV features a dual-antenna with telemetry power of up to 100mw and works quite happily with a 1S Lipo receiver battery.

The ER8GV receiver has been specially designed for glider pilots who require a compact and slim receiver with a built-in high-precision air pressure vario. It can drive up to 8 servos and has built-in receiver voltage telemetry and flight battery telemetry with the ability to automatically detect which voltage input to use. The ER8GV features a dual-antenna with telemetry power of up to 100mw and works quite happily with a 1S Lipo receiver battery.

The RadioMaster RP V2 series of receivers now have a built-in TCXO (Temperature-Compensated Xtal Oscillator). The TCXO ensures high stability and accuracy in frequency control and compensates for temperature variations. This results in consistent and reliable signal reception, even in extreme temperature conditions. It also reduces frequency drift over time, providing long-term frequency stability and preventing signal degradation. This provides a superior performance in demanding environments and enhances the flight experiences.

The RP1 2.4GHz ELRS Nano receivers use the high-performance, revolutionary ExpressLRS open-source system. The Nano receivers were designed by the ExpressLRS development team, and feature the ESP8285 MCU and SX1280 RF chips. WiFi is built-in so that you can easily upgrade the firmware and configure the receiver using your PC or mobile phone. Other features of the V2 are an upgraded rigid antenna with a UFL socket and improved solder pads.

The RadioMaster RP V2 series of receivers now have a built-in TCXO (Temperature-Compensated Xtal Oscillator). The TCXO ensures high stability and accuracy in frequency control and compensates for temperature variations. This results in consistent and reliable signal reception, even in extreme temperature conditions. It also reduces frequency drift over time, providing long-term frequency stability and preventing signal degradation. This provides a superior performance in demanding environments and enhances the flight experiences.

The RP2 2.4GHz ELRS Nano receivers use the high-performance, revolutionary ExpressLRS open-source system. The Nano receivers were designed by the ExpressLRS development team, and feature the ESP8285 MCU and SX1280 RF chips. WiFi is built-in so that you can easily upgrade the firmware and configure the receiver using your PC or mobile phone. Other features of the RP2 V2 are improved solder pads and a super lightweight built-in ceramic antenna.

The RadioMaster RP V2 series of receivers now have a built-in TCXO (Temperature-Compensated Xtal Oscillator). The TCXO ensures high stability and accuracy in frequency control and compensates for temperature variations. This results in consistent and reliable signal reception, even in extreme temperature conditions. It also reduces frequency drift over time, providing long-term frequency stability and preventing signal degradation. This provides a superior performance in demanding environments and enhances the flight experiences.

The RP2 2.4GHz ELRS Nano receivers use the high-performance, revolutionary ExpressLRS open-source system. The Nano receivers were designed by the ExpressLRS development team, and feature the ESP8285 MCU and SX1280 RF chips. WiFi is built-in so that you can easily upgrade the firmware and configure the receiver using your PC or mobile phone. Other features of the RP2 V2 are improved solder pads and a super lightweight built-in ceramic antenna.

The RP3 2.4GHz ELRS Nano receivers use the high-performance, revolutionary ExpressLRS open-source system. The ExpressLRS development team designed the Nano receivers, which feature the ESP8285 MCU and SX1280 RF chips. This offers Lora and FLRC 2.4GHz RF links for incredible range and low latency. WiFi is built-in to easily upgrade the firmware and configure the receiver using your PC or mobile phone.

The receiver features a Skyworks SE2431L providing an LNA for improved receiver performance, a PA providing up to 100mW of telemetry performance, and antenna switching for antenna diversity.. The RP3 Nano receiver is available in either an FCC or a European LBT version, please check the specifications below for the supported protocol.

The RP3 2.4GHz ELRS Nano receivers use the high-performance, revolutionary ExpressLRS open-source system. The ExpressLRS development team designed the Nano receivers, which feature the ESP8285 MCU and SX1280 RF chips. This offers Lora and FLRC 2.4GHz RF links for incredible range and low latency. WiFi is built-in to easily upgrade the firmware and configure the receiver using your PC or mobile phone.

The receiver features a Skyworks SE2431L providing an LNA for improved receiver performance, a PA providing up to 100mW of telemetry performance, and antenna switching for antenna diversity.. The RP3 Nano receiver is available in either an FCC or a European LBT version, please check the specifications below for the supported protocol.

RMILECアダプタコンバータ会はSBUS受信機に簡単に接続できるようにする最適なソリューションです。 T4363NB18アダプタは、5V電源をサポートし、12FGまたは14MZ送信機を一致させるためだけでなく、使用することができるだけでなく、個々の中継局としての別の場所に配置することができます。

ボードはハードウェアは、JSTのバッテリコネクタ、オン/オフスイッチ、端子、什器備品などとの完全な供給されています。

ご注意：オン/オフスイッチと端末のはんだ付けが必要です。

仕様：
素材：PCB
重量：39.65グラム
寸法：90×115ミリメートル

FrSky TFR6 7CH 2.4GHzのレシーバーFASST互換性

互換性：
FASSTの2.4G： エアシステム（7CHモード/マルチモード）
FrSky TFモジュール：TF-8M、TF-14M


特徴：
軽量かつ小型
2つの選択可能なフェイルセーフの設定オプション


仕様：
チャンネル数：7
動作電圧範囲：3.5V〜10V
動作温度範囲：-10℃〜60℃
外形寸法：37 * 22 * 8ミリメートル
重量：7.8グラム

PWMデコーダへFrSky S.BUSは、あなたのS.BUS対応受信機で任意の標準アナログまたはデジタルサーボを使用することができます。これは、あなたのモデルの既存のサーボを使用できるように高価S.BUS特定のサーボを使用する必要がなくなります。

唯一のあなたの受信機から1入力リードを接続しながら4プログラマブル・チャンネル出力を搭載し、あなたが独立してお好みのチャンネルに各サーボを割り当てることができます。これはあなたの配線がはるかに整然となり、複数の延長リードを実行するための必要性なしであなたのサーボの簡単設定アップを可能にします。

これは私たちのオレンジ7CHと9CH S.BUS互換受信機と組み合わせて使用​​するのに最適なデバイスです！

含まれています：
PWMデコーダへFrSky S.BUS

仕様：
チャンネル出力：4プログラマブル
リード線長は出力リレーチャンネル：200ミリメートル
全長：350ミリメートル

*注：FrSkyサーボチャンネルチェンジャーが必要（別売、下記の関連項目を参照してください）チャネル出力の割り当てを変更します。

Futuba FASSTとの互換性は、コロナR14FAは双葉ラジオのユーザーのための手頃な価格の代替手段を提供していますトランスミッタ。

仕様：
動作電流：
FASST 7CHモードノーマルと110ミリアンペアマックス@ 70ミリアンペア、
FASST通常のマルチチャンネルモード、110ミリアンペアマックス@ 80ミリアンペア
動作電圧：4.0〜10V
レイテンシ：
7mS高速PPM（HS）のために、14mS低速PPM（LS）@ FASSTマルチチャンネルモードのため、
8msの高速PPM（HS）、低速PPMのための16msの（LS）@ FASST 7CHモードの
感度：-96dBm〜
フェイルセーフ：はい
サイズ：53x37x16mm
重量：22グラム
アンテナの長さ：136ミリメートル

互換性：
FUTABA FASST 2.4GHzの送信機
TM7、TM8、TM10、TM14、6EX-2.4G、7C-2.4G、8FG、10CG、12FG