Chargeurs et accessoires RC

Alimentez vos appareils électriques compatibles avec le 4mm HXT à DC convertisseur de prise. Le convertisseur DC Jack a deux 2mm connecteurs jack (centres positifs) et est idéal pour alimenter des chargeurs ou des éléments électriques similaires.

Spécifications:
Longueur: 210mm
DC Jack: 2mm
Connecteur de batterie: 4mm HXT

La plupart des packs de batteries lithium-polymère 7S standard comprennent deux ports d'équilibre, un équilibre de plomb 4S et 3S (total 7S). Cela rend difficile de charger avec la plupart des chargeurs de batterie standard qui ne disposent d'un port de la balance.

Avec cet adaptateur super utile, vous pouvez facilement charger votre batterie 7S avec un chargeur de solde 8 ~ 10S capable standard qui accepte JST-XH bouchons d'équilibre. Cet adaptateur prend les 4S et 3S fiches individuelles de votre paquet, et les combine à une bougie d'équilibre 7S unique qui est capable de se connecter à la plupart des 8 ~ 10S chargeurs capables standard.

Spécifications:
Entrée: 1 x 4S et le bouchon de la balance 1 x 3S JST-XH
Bouchon de balance 7S JST-XH: Sortie
Longueur: 100mm

HXT 4mm Adaptateur Batterie T-Connector Lead (2pc)

Cet adaptateur permet de convertir une batterie HXT 4mm équipé d'un connecteur en T pour une utilisation avec un ESC équipé T-Connector ou le plomb de charge.

Spec:
Poids: 7g (Chaque)

Utilisez cet adaptateur pour convertir une avance de charge XT-60 pour charger JST équipé batteries.

This simple and effective charge lead comes pre-soldered with standard 4mm bullet connectors at the charger end and has stepped, bullet connectors at the battery end allowing you to charge hard case packs that utilise 4mm and 5mm connectors. 

This adapter will convert an HXT 5.5mm bullet equipped battery to an XT90 for use with an XT90 equipped ESC or an XT90 Charge lead.

This adapter will convert an XT90 equipped battery to an HXT 5.5mm bullet for use with an HXT 5.5mm bullet equipped ESC or an HXT 5.5mm bullet Charge lead.

XT30U Silicone Charge Lead with 4mm Banana Plugs.

An excellent, low resistance, flexible silicone charge lead with standard 4mm banana plugs on one end and a set of XT150/AS150 on the other. The Amass XT150/AS150 is a 7mm anti-spark connector rated at up to 150amps, and the 4mm banana plugs suits most chargers on the market today.

Specs:
Battery Connector: XT150/AS150 (7mm)
Charger Connection: 4mm Banana Plug
Wire Diameter: 14AWG
Wire: Tinned copper
Wire Insulation: Silicone rubber
Length: 300mm
Weight: 37.3g

Designed in-house by HobbyKing, this Turnigy parallel charge board can charge up to 6 LiPo or LiHV packs of the same capacity and cell count at the same time. The board is supplied with TRA connectors for the main charging leads, an XT60 lead to plug into the charger, and 2~6S JST-XH connectors for the balancing leads. The board is fused for protection and a 6S JST-XH adaptor lead is also supplied to connect the board to your charger balancing input.

Designed in-house by HobbyKing, this Turnigy parallel charge board can charge up to 6 LiPo or LiHV packs of the same capacity and cell count at the same time. The board is supplied with EC3 connectors for the main charging leads, an XT60 lead to plug into the charger, and 2~6S JST-XH connectors for the balancing leads. The board is fused for protection and a 6S JST-XH adaptor lead is also supplied to connect the board to your charger balancing input.

Designed in-house by HobbyKing, this Turnigy parallel charge board can charge up to 6 LiPo or LiHV packs of the same capacity and cell count at the same time. The board is supplied with EC5 connectors for the main charging leads, an XT60 lead to plug into the charger, and 2~6S JST-XH connectors for the balancing leads. The board is fused for protection and a 6S JST-XH adaptor lead is also supplied to connect the board to your charger balancing input.

Designed in-house by HobbyKing, this Turnigy parallel charge board can charge up to 6 LiPo or LiHV packs of the same capacity and cell count at the same time. The board is supplied with TR connectors for the main charging leads, a pair of 4mm banana plugs to connect to the charger, and 2~6S JST-XH connectors for the balancing leads. The board is fused for protection and a 6S JST-XH adaptor lead is also supplied to connect the board to your charger balancing input.

Designed in-house by HobbyKing, this Turnigy parallel charge board can charge up to 6 LiPo or LiHV packs of the same capacity and cell count at the same time. The board is supplied with EC3 connectors for the main charging leads, a pair of 4mm banana plugs to connect to the charger, and 2~6S JST-XH connectors for the balancing leads. The board is fused for protection and a 6S JST-XH adaptor lead is also supplied to connect the board to your charger balancing input.

Le câble adaptateur ToolkitRC SC100 est utilisé pour alimenter des chargeurs de batterie à faible puissance ou d'autres appareils avec un connecteur d'entrée XT60 à partir d'une alimentation USB-C jusqu'à 100 W.

Spécifications:
Type: câble de protocole ToolkitRC SC100 XT60 ~ USB-C
Entrée: USB-C 5.0~20V@PD2.0/PD3.0/QC2.0
Tension de sortie: 5 ~ 20 V max.
Courant de sortie: 5 A max.
Connecteur de sortie: XT60
Longueur: 50cm
Poids: 35g