Распродажа

This next-generation bidirectional cross weave glass fiber reinforcing tape has a transparent "PET" substrate which provides a high longitudinal tensile strength, and is transverse tear resistance, in short, it is extremely strong. The other outstanding property it has is the adhesive, it is super sticky, but allows for positioning. Once you are satisfied with the position of the tape gently apply more pressure and the strength of the bond increases. This strong, pressure-sensitive rubber-based adhesive will also increase its strength over the next 24hrs as it "cures" to form a permanent, very strong bond. Another characteristic of this tape is that it will retain its strength in high and low temperatures.

The FTM302 adopts FLYSKY's third-generation automatic frequency hopping digital system, AFHDS 3. It uses a single antenna, a bidirectional transmission system in a compact design with support for multiple signal inputs. Supports external power and is compatible with standard JR-type module bays.

The FTM302 offers a long range of up to 3.5km + on the EU default setting of 20dBm (changeable through the management system), low latency, less than 10ms, and allows for online updates and managing the module via the FLYSKY Remote Control Assistant. Power to the module can either be internal, or an external power source of 5~28V can be connected via the built-in XT30 connector. The module also has a built-in fan which automatically turns on if the temperature reaches 45°C to ensure the system remains safe, this can happen when the module is being used with higher voltages.

This is a replacement pre-painted horizontal stabilizer for the H-King Yak-11 Red Reno Racer.

This is a replacement pre-painted vertical stabilizer for the H-King Yak-11 Red Reno Racer.

This is a replacement pre-painted vertical stabilizer for the H-King Yak-11 Commemorative Russian WW2 Warbird.

This is a replacement pre-painted canopy and battery hatch for the H-King Yak-11 Red Reno Racer.

This is a replacement pre-painted canopy and battery hatch for the H-King Yak-11 Commemorative Russian WW2 Warbird.

This is a replacement pair of gear doors, oleo's, and wheels for the H-King Yak-11 Red Reno Racer.

This is a replacement pair of gear doors, oleo's, and wheels for the H-King Yak-11 Commemorative Russian WW2 Warbird.

A replacement wing joiner/main spar for the H-King Yak-11 Red Reno Racer/Commemorative Russian WW2 Warbird.

This is a replacement decal set for the H-King Yak-11 Red Reno Racer.

Хотите еще больше скорости и мощности для своего H-King Reno Aces P-51 "Galloping Ghost"? Затем перейдите на дополнительную мощную бесщеточную ракету Pro 3108-1160KV и превратите ее в баллистическую ракету с неограниченными вертикальными характеристиками. Нет необходимости менять поставляемый гребной винт или ESC, с этим обновлением подойдут и те, и другие.

A strong, flexible, transparent fuel tank that is suitable for most types of RC models. The fuel tank includes a machined metal cap with fuel feed, a flexible fuel feed pipe with clunk weight, and 2 factory-installed machined metal 90° hose attachment nipples. One of these is for filling the tank, and the other is used for pressure or venting. Each fuel tank comes with a Turnigy sticker that includes the capacity of the tank, this can be attached to the tank in a convenient position to remind you of its size. The fuel tank is suitable for use with both gas and nitro fuels.

A replacement crankshaft set for the Turnigy TP10 10cc gas engine. This set includes the crankshaft, conrod, prop-driver woodruff key, and prop nut.

A replacement crankcase set for the Turnigy TP10 10cc gas engine, this set includes the crankcase, gasket, and 2 x screws.

A replacement prop driver set for the Turnigy TP10 10cc gas engine. This set includes the prop driver with inset magnet, prop washer, and woodruff key.

A replacement crankcase for the Turnigy TP26 26cc gas engine.

Высококачественная двусторонняя лента, которая идеально подходит для закрепления сервоприводов, приемников и многих других предметов в ваших моделях. Он изготовлен из амортизирующего пенополиэтилена с прочным акриловым клеем, нанесенным с обеих сторон. Этот пенополиуретан идеально подходит для изоляции чувствительных электронных компонентов от вибрации. Другие особенности ленты - водостойкость, термостойкость и защита от ультрафиолета.

A replacement pair of main landing gear retaining plates for the Durafly Tundra V2/V3 and Night Tundra.

Note: This replacement spare part for the Durafly Tundra V2 is not compatible with the Tundra V1.

A replacement horizontal and vertical stabilizer set with elevators, rudder, and factory-applied decals for the Civilian Cargo version of the Avios C-130 V2.  Please note that this spare part is not suitable for the original versions of the C-130.

A replacement 6.5x5 4 blade standard pitch propeller with backplate and screw for both versions of the Avios C-130 V2, is also suitable for the version 1 of the C-130.

A replacement 6.5x5 4 blade reverse pitch propeller with backplate and screw for both versions of the Avios C-130 V2, is also suitable for the version 1 of the C-130.

A complete replacement set of decals for the Civilian Cargo version of the Avios C-130 V2.

Accurately drill your propellers for your TP 35cc gas engine with this easy-to-use drilling jig. The jig is CNC machined from aluminum stock and is supplied with a clamping screw to hold the propeller secure whilst drilling.

A replacement set of scale detailing parts for the AVIOS KingTwin 1700.

A replacement prop adapter for the H-King Reno Aces P-51 "Galloping Ghost".

A replacement set of 10x6 left and right propellers for the AVIOS KingTwin.

Please note: These propellers are also suitable for the AVIOS BushMule and Albatross models.

A replacement set of main and nosewheel landing gear struts for the AVIOS KingTwin. 

A replacement canopy and battery hatch for the H-King F-16 Fighting Falcon 550mm.

A replacement pair of horizontal stabilizers with elevators for the H-King F-16 Fighting Falcon 550mm.

A replacement vertical stabilizer with factory-applied decals for the H-King F-16 Fighting Falcon 550mm.

A replacement carbon wing spar for the H-King F-16 Fighting Falcon 550mm.

A replacement 4S 50mm 12 blade ducted fan unit with brushless motor for the H-King F-16 Fighting Falcon 550mm.

A replacement canopy and battery hatch for the H-King F-18 Super Hornet 588mm.

A replacement pair of vertical stabilizers with factory-applied decals for the H-King F-18 Super Hornet 588mm.