Радиоусилители

These are a good quality servo Y lead with the JR style 1 x male and 2 x female connectors fitted. These Y leads are perfect for running 2 servos from the one receiver servo port.

These are good quality twisted servo extension leads with a Futaba style male connector one end and a female connector on the other. These are ideal for connecting servos in wings or down the tail end of fuselages etc. Twisting wires together reduces the possibility of radiation which in turn reduces the risk of radio interference and glitching.

These are good quality twisted leads with a Futaba style male connector on one end. Twisting wires together reduces the possibility of radiation which in turn reduces the risk of radio interference and glitching.

These Futaba style 30cm servo extension leads feature a retaining clip on the female end for a positive lock, perfect for those installations hidden away in wings and fuselages etc.

These are a good quality servo Y lead with the Futaba style 1 x male and 2 x female connectors fitted. These Y leads are perfect for running 2 servos from the one receiver servo port.

High gain, high sensitivity RF components are used throughout, this coupled with FLYSKY's latest generation intelligent wireless 2.4GHz AFHDS 3 protocol, enables the receiver to reject interference easily, while maintaining high reception rates, and stable performance. This version 2 FGr4 supports PPM, i-BUS, and 4 PWM data outputs (CH1~CH4), and an input for connecting additional sensors. Another feature of this quality FLYSKY receiver is the ability to handle a wide input voltage, anything from 3.5-12V can be used, and the case has a sealing gasket which makes it water-resistant.

Power HD servos are reknown for build quality and reliability, the TR-4 micro digital waterproof servo is no exception. This servo is perfect for smaller models such as crawlers, buggies, boats and even water/float planes where waterproofing is necessary. The case is sealed with rubber gaskets and O rings and the gear train is metal except for one sacrificial plastic gear. This helps stop permanent damage being done to the servo in the case of a really hard knock. The servo is supplied with 2 x single arm output horns and an M3 servo horn screw.

The FGr8B surface micro receiver adopts FLYSKY's third-generation automatic frequency hopping digital system (AFHDS 3), it is perfectly suited to their range of PL18, NB4, and NB4 Lite transmitters. It uses a single antenna bidirectional transmission system that is uniquely designed to install and output PWM/PPM, and iBUS in signals.

The FTr10 adopts FLYSKY's third-generation automatic frequency hopping digital system, AFHDS 3. It uses a double-antenna, bidirectional transmission system to save space and supports standard PPM, S-Bus, and i-Bus signals.

The FTr10 is a small, lightweight 2.4GHz receiver that will accept a wide input voltage of between 3.5~18V, has an incredible range in interference-free open areas of up to 10km, and its unique design includes i-BUS, S-BUS, PPM, PWM, and UART data ports. It has the ability to update firmware online and is compatible with the FLYSKY Paladin PL18 radio system. With all these features it is the perfect choice for drone flying, drone racing, FPV, and other long-range applications.

The FTM302 adopts FLYSKY's third-generation automatic frequency hopping digital system, AFHDS 3. It uses a single antenna, a bidirectional transmission system in a compact design with support for multiple signal inputs. Supports external power and is compatible with standard JR-type module bays.

The FTM302 offers a long range of up to 3.5km + on the EU default setting of 20dBm (changeable through the management system), low latency, less than 10ms, and allows for online updates and managing the module via the FLYSKY Remote Control Assistant. Power to the module can either be internal, or an external power source of 5~28V can be connected via the built-in XT30 connector. The module also has a built-in fan which automatically turns on if the temperature reaches 45°C to ensure the system remains safe, this can happen when the module is being used with higher voltages.

The FTr4 adopts FLYSKY's third-generation automatic frequency hopping digital system, AFHDS 3. It uses a single antenna, bidirectional transmission system to save space and supports standard PPM, S-Bus, and i-Bus signals.

The FTr4 is a small, lightweight 2.4GHz receiver that will accept an input voltage of between 3.5~8.4V, has a range in interference-free open areas of up to 500m, and its unique design includes i-BUS, S-BUS, PPM, and PWM data ports. It has the ability to update firmware online and is compatible with the FLYSKY Paladin PL18, and NB4 radio systems. With all these features it is the perfect choice for drone flying, gliding, and small fixed-wing aircraft.

An optional CNC, anodized metal folding handle that will fit most of the RADIOMASTER multi-protocol series of transmitters.

Complement your RADIOMASTER TX16S transmitter with these very smart and comfortable leather side grips. These grips are made of brown leather,  other colors are available.

A replacement ORX 3-Axis gyro for the Durafly Prime Tundra PT1200 STOL Trainer-Sports Model.

Features:
• Gyro stability for roll, pitch, and yaw
• Small and lightweight
• Easy set-up
• 3 modes: Gyro off/Gyro on/Trainer mode

Gyro off means no stabilization from the gyro at all. Gyro on gives some gyro stability and full control surface deflection. Trainer mode gives a lot more gyro stability, and also limits the amount of control deflection, will also self-right the model to a normal flying attitude.

The OrangeRx R615X offers true DSMX compatibility and utilizes a dual antenna system to provide true signal reception diversity. Due to the previously used IC becoming obsolete, this latest R615X receiver has been redesigned, and now offers improved range and performance. Features that have been retained are the programmable failsafe on binding, ultra-fast brown-out recovery, and wide voltage input range. As we can maintain the same low price as before, this makes the latest R615X still unbeatable value for money.

This optional magnetic release servo for the Durafly Me-163b V2 allows you to determine when to release the take-off dolly, rather than rely on gravity. It is particularly beneficial if you operate your Me-163b off of a bumpy strip where the model may prematurely jump off of the dolly. It is simple and straightforward to install, and the servo lead is normally plugged into the assigned retract socket of your receiver. The unit is supplied with a magnet which needs to be glued into the top of the take-off dolly.

Please note:  This option part is also suitable for earlier versions of the Durafly Me-163.

This is the perfect protection for the transport and storage of your precious R/C transmitter.  It features lightweight construction, yet is rigid enough to protect your transmitter during transportation. It has dual zippers, a removable carrying strap, and pockets inside to accommodate a wide variety of accessories such as a spare TX battery, charger, neck strap, and much more!

Two self-adhesive foam blocks are included for the inside so you can adjust these as necessary to accommodate your specific transmitter. Also, these include hook & loop backing so they can be moved to whichever position you require very quickly and easily. A hook & loop strap is integrated into the bag to ensure your transmitter stays put.

Specs:
Inner Dimensions: 290x190x100mm
Weight: 450g
Color: Grey/Orange

This is the perfect protection for the transport and storage of your precious R/C transmitter. It features lightweight construction, yet is rigid enough to protect your transmitter during transportation. It has dual zippers, a removable carrying strap, and pockets inside to accommodate a wide variety of accessories such as a spare TX battery, charger, neck strap, and much more!

Two self-adhesive foam blocks are included for the inside so you can adjust these as necessary to accommodate your specific transmitter. Also, these include hook & loop backing so they can be moved to whichever position you require very quickly and easily. A hook & loop strap is integrated into the bag to ensure your transmitter stays put.

Specs:
Inner Dimensions: 290x190x100mm
Weight: 450g
Color: Red/Grey

This is the perfect protection for the transport and storage of your precious R/C transmitter. It features lightweight construction, yet is rigid enough to protect your transmitter during transportation. It has dual zippers, a removable carrying strap, and pockets inside to accommodate a wide variety of accessories such as a spare TX battery, charger, neck strap, and much more!

Two self-adhesive foam blocks are included for the inside so you can adjust these as necessary to accommodate your specific transmitter. Also, these include hook & loop backing so they can be moved to whichever position you require very quickly and easily. A hook & loop strap is integrated into the bag to ensure your transmitter stays put.

Specs:
Inner Dimensions: 290x190x100mm
Weight: 450g
Color: Black/Orange

The BMS-622DMG digital servo is perfect for planes, helicopters, boats, vehicles (GP & EP), and robotics. Being digital, the quoted torque is not only when the servo is moving, but also the holding power when the servo arm is stationary and under load. The servo has an impressive output torque of 10.6kg and an excellent speed of 0.13 sec when using a 6V power source. The gear train has metal gears, a dual ball-raced output shaft, and also a silver anodized metal heatsink to keep the components cool when operating under extreme conditions, this prolongs the life of the servo. The BMS-622DMG is supplied with the universal "S" type connector, same as JR, etc, and a complete servo accessory pack with arms and mounting hardware.

The BMS-662MG is perfect for planes, helicopters, boats, vehicles (GP & EP), and robotics. The servo has an impressive output torque of 14.2kg and an excellent speed of 0.17 sec when using a 6V power source. The gear train has metal gears, a dual ball-raced output shaft, and also a red anodized metal heatsink to keep the components cool when operating under extreme conditions, this prolongs the life of the servo. The BMS-662MG is supplied with the universal "S" type connector, same as JR, etc, and a complete servo accessory pack with arms and mounting hardware.

The BMS-632MG is perfect for planes, helicopters, boats, vehicles (GP & EP), and robotics. The servo has an impressive output torque of 14.6kg and an excellent speed of 0.15 sec when using a 6V power source. The gear train has metal gears and a dual ball-raced output shaft. The BMS-632MG is supplied with the universal "S" type connector, same as JR, etc, and a complete servo accessory pack with arms and mounting hardware.

The BMS-622MG is perfect for planes, helicopters, boats, vehicles (GP & EP), and robotics. The servo has an impressive output torque of 10.6kg and an excellent speed of 0.13sec when using a 6V power source. The gear train has metal gears and a dual ball-raced output shaft. The BMS-622MG is supplied with the universal "S" type connector, same as JR, etc, and a complete servo accessory pack with arms and mounting hardware.

The BMS-380MAX is perfect for sailplanes, electric-powered gliders, small electric cars, and also as a wing servo as it is only 13mm wide. The servo has an impressive output torque of 4.7kg and an excellent speed of 0.14sec when using a 6V power source. The gear train has helical metal gears, and the ball-raced output shaft has a 25-tooth spline identical to Futaba specs. The BMS-380MAX is supplied with the universal "S" type connector, same as JR, etc, and a complete servo accessory pack with arms and mounting hardware.

The GS2010MG is a fast (0.10sec), high torque (23.5kg), metal-geared standard-size servo with an amazing rotation of 270°. This makes it very suitable for a variety of applications including robotics, or as a sail winch for a model yacht. The servo is supplied with a mounting kit and a selection of plastic servo horns, plus one metal servo horn.

Specs:
Model No: GS2010MG
Torque@5V: 21kg
Torque@6.8V: 23.5kg
Speed@5V: 0.12sec/60°
Speed@6.8V: 0.10sec/60°
Rotation: 270°
Gear Train: Metal
Bearings: Twin BB
Motor: Iron core
Amplifier: Digital
Dimensions: 40x20x40.5mm
Weight: 60g

The GS3009MG is a fast (0.09sec), high torque (38kg), metal-geared standard-size servo with an amazing rotation of 270°. This makes it very suitable for a variety of applications including robotics, or as a sail winch for a model yacht. The servo is supplied with a mounting kit and a selection of plastic servo horns, plus one metal servo horn.

Specs:
Model No: GS3009MG
Torque@5V: 28.5kg
Torque@6.8V: 38kg
Speed@5V: 0.11sec/60°
Speed@6.8V: 0.09sec/60°
Rotation: 270°
Gear Train: Metal
Bearings: Twin BB
Motor: Iron core
Amplifier: Digital
Dimensions: 40x20x40.5mm
Weight: 60g

The GS2505MG is a fast (0.05sec), high torque (39kg), metal-geared standard-size servo with an amazing rotation of 270°. This makes it very suitable for a variety of applications including robotics, or as a sail winch for a model yacht. The servo is supplied with a mounting kit and a selection of plastic servo horns, plus one metal servo horn.

Specs:
Model No: GS2505MG
Torque@5V: 26kg
Torque@8.4V: 39kg
Speed@5V: 0.10sec/60°
Speed@8.4V: 0.05sec/60°
Rotation: 270°
Gear Train: Metal
Bearings: Twin BB
Motor: Coreless
Amplifier: Digital
Dimensions: 40x20x40.5mm
Weight: 60g

The GS3508MG is a fast (0.08sec), high torque (45kg), metal-geared standard-size servo with an amazing rotation of 270°. This makes it very suitable for a variety of applications including robotics, or as a sail winch for a model yacht. The servo is supplied with a mounting kit and a selection of plastic servo horns, plus one metal servo horn.

Specs:
Model No: GS3508MG
Torque@5V: 31kg
Torque@8.4V: 45kg
Speed@5V: 0.14sec/60°
Speed@8.4V: 0.08sec/60°
Rotation: 270°
Gear Train: Metal
Bearings: Twin BB
Motor: Coreless
Amplifier: Digital
Dimensions: 40x20x40.5mm
Weight: 60g

The GS2508MG is a fast (0.08sec), high torque (25kg), metal-geared standard-size servo with an amazing rotation of 270°. This makes it very suitable for a variety of applications including robotics, or as a sail winch for a model yacht. The servo is supplied with a mounting kit and a selection of plastic servo horns, plus one metal servo horn. The entire servo case is CNC machined from solid 6061 aluminum, which is extremely strong and acts as a very good heatsink for the motor and amplifier.

Specs:
Model No: GD2508MG
Torque@6V: 18kg
Torque@8.4V: 25kg
Speed@6V: 0.13sec/60°
Speed@8.4V: 0.08sec/60°
Rotation: 270°
Gear Train: Metal
Bearings: Twin BB
Motor: Iron core
Amplifier: Digital
Dimensions: 40x20x40mm
Weight: 78g

The GD3511MG is a quick (0.11sec), high torque (35kg), metal-geared standard-size servo with an amazing rotation of 270°. This makes it very suitable for a variety of applications including robotics, or as a sail winch for a model yacht. The servo is supplied with a mounting kit and a selection of plastic servo horns, plus one metal servo horn. The entire servo case is CNC machined from solid 6061 aluminum, which is extremely strong and acts as a very good heatsink for the motor and amplifier.

Specs:
Model No: GD3511MG
Torque@6V: 28kg
Torque@8.4V: 35kg
Speed@6V: 0.20sec/60°
Speed@8.4V: 0.11sec/60°
Rotation: 270°
Gear Train: Metal
Bearings: Twin BB
Motor: Iron core
Amplifier: Digital
Dimensions: 40x20x40mm
Weight: 78g

The GC3507MG is a very fast (0.07sec), high torque (35kg), metal-geared standard-size servo with an amazing rotation of 270°. This makes it very suitable for a variety of applications including robotics, or as a sail winch for a model yacht. The servo is supplied with a mounting kit and a selection of plastic servo horns, plus one metal servo horn. The entire servo case is CNC machined from solid 6061 aluminum, which is extremely strong and acts as a very good heatsink for the motor and amplifier.

Specs:
Model No: GC3507MG
Torque@6V: 30kg
Torque@8.4V: 35kg
Speed@6V: 0.09sec/60°
Speed@8.4V: 0.07sec/60°
Rotation: 270°
Gear Train: Metal
Bearings: Twin BB
Motor: Coreless
Amplifier: Digital
Dimensions: 40x20x40mm
Weight: 75g

The GC4509MG is a very fast (0.09sec), high torque (45kg), metal-geared standard-size servo with an amazing rotation of 270°. This makes it very suitable for a variety of applications including robotics, or as a sail winch for a model yacht. The servo is supplied with a mounting kit and a selection of plastic servo horns, plus one metal servo horn. The entire servo case is CNC machined from solid 6061 aluminum, which is extremely strong and acts as a very good heatsink for the motor and amplifier.

Specs:
Model No: GC4509MG
Torque@6V: 35kg
Torque@8.4V: 45kg
Speed@6V: 0.13sec/60°
Speed@8.4V: 0.09sec/60°
Rotation: 270°
Gear Train: Metal
Bearings: Twin BB
Motor: Coreless
Amplifier: Digital
Dimensions: 40x20x40mm
Weight: 78g

The GB3506MG is a very fast (0.06sec), brushless, high torque (35kg), metal-geared standard-size servo with an amazing rotation of 270°. This makes it very suitable for a variety of applications including robotics, or as a sail winch for a model yacht. The servo is supplied with a mounting kit and a selection of plastic servo horns, plus one metal servo horn. The entire servo case is CNC machined from solid 6061 aluminum, which is extremely strong and acts as a very good heatsink for the motor and amplifier.

Specs:
Model No:  GB3506MG
Torque@6V: 30kg
Torque@8.4V: 35kg
Speed@6V: 0.09sec/60°
Speed@8.4V: 0.06sec/60°
Rotation: 270°
Gear Train: Metal
Bearings: Twin BB
Motor: Brushless
Amplifier: Digital
Dimensions: 40x20x40mm
Weight: 75g

The GD2508MG is a fast (0.08sec), high torque (25kg), metal-geared standard-size servo with a rotation of 180°, supplied with a mounting kit, and a selection of plastic servo horns, plus one metal servo horn.  The entire servo case is CNC machined from solid 6061 aluminum, which is extremely strong and acts as a very good heatsink for the motor and amplifier.

Specs:
Model No: GD2508MG
Torque@6V: 18kg
Torque@8.4V: 25kg
Speed@5V: 0.13sec/60°
Speed@8.4V: 0.08sec/60°
Rotation: 180°
Gear Train: Metal
Bearings: Twin BB
Motor: Iron core
Amplifier: Digital
Dimensions: 40x20x40mm
Weight: 78g

The GD3511MG is a fast (0.11sec), high torque (35kg), metal-geared standard-size servo with a rotation of 180°, supplied with a mounting kit, and a selection of plastic servo horns, plus one metal servo horn. The entire servo case is CNC machined from solid 6061 aluminum, which is extremely strong and acts as a very good heatsink for the motor and amplifier.

Specs:
Model No: GD3511MG
Torque@6V: 28kg
Torque@8.4V: 35kg
Speed@6V: 0.20sec/60°
Speed@8.4V: 0.11sec/60°
Rotation: 180°
Gear Train: Metal
Bearings: Twin BB
Motor: Iron core
Amplifier: Digital
Dimensions: 40x20x40mm
Weight: 78g