$10 - $49.99

FrSky M7-R hall sensor gimbal is specially designed for FPV racing, 3D and acrobatic fixed wing and 3D Heli pilots who are using the FrSky Taranis Q X7/X7S Transmitter. The 45°throttle travel will allow you to achieve a quick throttle response resulting in precision control.

After the huge success of the Turnigy Evolution, the engineers at Turnigy listened to customer feedback, went back to the drawing board, and came up with the exciting Turnigy Evolution PRO. As with the Evolution, the Evolution PRO is designed with the drone flier in mind and is still amazingly compact for easy backpack transportation.

This kit comes complete with the FrSky Taranis X-Lite BRACE. There are also red replacement gimbal stick ends in two sizes, short and long, depending on your needs.

High gain, high sensitivity RF components are used throughout, this coupled with FLYSKY's latest generation intelligent wireless 2.4GHz AFHDS 3 protocol, enables the receiver to reject interference easily, while maintaining high reception rates, and stable performance. This version 2 FGr4 supports PPM, i-BUS, and 4 PWM data outputs (CH1~CH4), and an input for connecting additional sensors. Another feature of this quality FLYSKY receiver is the ability to handle a wide input voltage, anything from 3.5-12V can be used, and the case has a sealing gasket which makes it water-resistant.

The FGr8B surface micro receiver adopts FLYSKY's third-generation automatic frequency hopping digital system (AFHDS 3), it is perfectly suited to their range of PL18, NB4, and NB4 Lite transmitters. It uses a single antenna bidirectional transmission system that is uniquely designed to install and output PWM/PPM, and iBUS in signals.

The FTM302 adopts FLYSKY's third-generation automatic frequency hopping digital system, AFHDS 3. It uses a single antenna, a bidirectional transmission system in a compact design with support for multiple signal inputs. Supports external power and is compatible with standard JR-type module bays.

The FTM302 offers a long range of up to 3.5km + on the EU default setting of 20dBm (changeable through the management system), low latency, less than 10ms, and allows for online updates and managing the module via the FLYSKY Remote Control Assistant. Power to the module can either be internal, or an external power source of 5~28V can be connected via the built-in XT30 connector. The module also has a built-in fan which automatically turns on if the temperature reaches 45°C to ensure the system remains safe, this can happen when the module is being used with higher voltages.

The RadioMaster RP V2 series of receivers now have a built-in TCXO (Temperature-Compensated Xtal Oscillator). The TCXO ensures high stability and accuracy in frequency control and compensates for temperature variations. This results in consistent and reliable signal reception, even in extreme temperature conditions. It also reduces frequency drift over time, providing long-term frequency stability and preventing signal degradation. This provides a superior performance in demanding environments and enhances the flight experiences.

The RP2 2.4GHz ELRS Nano receivers use the high-performance, revolutionary ExpressLRS open-source system. The Nano receivers were designed by the ExpressLRS development team, and feature the ESP8285 MCU and SX1280 RF chips. WiFi is built-in so that you can easily upgrade the firmware and configure the receiver using your PC or mobile phone. Other features of the RP2 V2 are improved solder pads and a super lightweight built-in ceramic antenna.

The RP3 2.4GHz ELRS Nano receivers use the high-performance, revolutionary ExpressLRS open-source system. The ExpressLRS development team designed the Nano receivers, which feature the ESP8285 MCU and SX1280 RF chips. This offers Lora and FLRC 2.4GHz RF links for incredible range and low latency. WiFi is built-in to easily upgrade the firmware and configure the receiver using your PC or mobile phone.

The receiver features a Skyworks SE2431L providing an LNA for improved receiver performance, a PA providing up to 100mW of telemetry performance, and antenna switching for antenna diversity.. The RP3 Nano receiver is available in either an FCC or a European LBT version, please check the specifications below for the supported protocol.

A replacement pair of wings with flaps and ailerons for the grey XFLY Alpha Jet.

A replacement pair of wings with flaps and ailerons for the blue "Patrouille de France" XFLY Alpha Jet.

A replacement pair of horizontal stabilizers for the grey XFLY Alpha Jet.

A replacement pair of horizontal stabilizers for the blue "Patrouille de France" XFLY Alpha Jet.

A replacement vertical stabilizer with rudder for the grey XFLY Alpha Jet.

A replacement vertical stabilizer with rudder for the blue "Patrouille de France" XFLY Alpha Jet.

A replacement gun pod for the grey XFLY Alpha Jet.

A replacement set of wheels for the XFLY Alpha Jet (3pcs).

A replacement front oleo strut with wheel for the XFLY Alpha Jet.

A replacement oleo strut with wheel and left side gear door for the grey XFLY Alpha Jet.

A replacement oleo strut with wheel and left side gear door for the blue "Patrouille de France" XFLY Alpha Jet.

A replacement oleo strut with wheel and right side gear door for the grey XFLY Alpha Jet.

A replacement multi-connector system for the XFLY Alpha Jet (2pcs).

A replacement fuselage for the 750mm XFLY T-7A Red Hawk.

A replacement pair of vertical stabilizers for the 750mm XFLY T-7A Red Hawk (2pcs).

A replacement set of main and nose wheel landing gear with wheels for the 750mm XFLY T-7A Red Hawk.

A replacement pair of horizontal stabilizers with rotating shafts for the 975mm XFLY T-7A Red Hawk (2pcs).

A replacement set of missiles and drop tank for the 975mm XFLY T-7A Red Hawk (7pcs).

A replacement set of wheels for the 975mm XFLY T-7A Red Hawk (3pcs).

Replacement multi-function control board for the 975mm XFLY T-7A Red Hawk.

A replacement nose gear servoless retract unit for the 975mm XFLY T-7A Red Hawk.

A replacement horizontal stabilizer with elevator for the XFLY Swift 2100mm Sport Glider.

This optional EDF nacelle unit will convert your XFLY Swift 2100 into an EDF-powered sport glider. The unit includes the XFLY Galaxy 64mm 12-blade fan, and the powerful XFLY 2840-3200KV brushless motor to give your Swift on a 4S battery an incredible performance. Installation is very straightforward, once installed you will only need to remove the prop and fit the supplied nose cone.

Specs:
Type: XFLY Swift 2100 Sport Glider Optional EDF Unit
Fan: 64mm 12-blade
Motor: 2840-3200KV brushless
Thrust: 1250g
Recommended Battery: 14.8V (4S) 2200~3300mAh LiPo (not supplied)

A replacement fuselage with nosegear for the red and white XFLY 850mm Partenavia P68 Twin.

A replacement wing set with ailerons for the red and white XFLY 850mm Partenavia P68 Twin.

A replacement fuselage for the grey 750mm XFLY Sukhoi Su-27 Flanker.

A replacement pair of wings for the grey 750mm XFLY Sukhoi Su-27 Flanker.